Connections; Normal Play - Denon DCM-370 Instrucciones De Operación

CONNECTIONS

(1) Connecting the Output Terminal
• Connect one end of the connection cord supplied with the CD Player to
the output terminals, left (L) and right (R) of the CD Player, and the other
end to the CD, AUX or TAPE PLAY input terminals, left (L) and right (R), of
the amplifier.
DCM-370/270
IN OUT COAXIAL
SYNCH O CON ROL D GIT L OUT
NE OUT
V RIAB E
(Amplifier)
SIGNAL
GND
SPEAKER SYSTEMS
R
NPUTS PB REC
PHONO CD TUNER AUX A E 1 TAPE 2 A E 1 TAPE 2
/DAT /MD /DAT /MD
L L
R
(2) Connecting the Digital Output Jack (COAXIAL) (DCM-370 only)
• Use a 75 Ω/ohm pin cord to connect the digital output jack (COAXIAL) of
the DCM-370 to the digital input jack (COAXIAL) on a digital processor or
MD recorder, available in stores.
DCM-370/270
IN OUT COAXIAL
S NCHRO CONTROL D GI AL OUT
INE OUT
VAR ABLE
Digital processor or MD recorder
D GITAL INPUT
COAX AL
OPT CAL

NORMAL PLAY

Follow the steps below to get an understanding of the disc play
procedure.
(1) Starting Playback
HD D
DCM 370
PCM AUD O TEC NOLOGY / D UTO CHANG R T ACK
EMO E
EN OR D SC ‚⁄ M N S C
¤ ‚‹ fi‚
5 DISC AUTOMATIC DISC LOAD NG SYSTEM
ON £ FF
PHON S
1. Turn the power switch on and press the open/close (
button to open the drawer.
2. Set the disc to be played in the front side tray.
3. Press the play button ( ).
1
4. The drawer closes and the disc just loaded is played.
5. The disc number, track number and elapsed time, etc., for the disc
currently playing appear on the display window.
6. If the open/close ( OPEN/CLOSE) button is pressed while a disc is
5
playing, playback continues, but the drawer opens and four discs can be
replaced. The disc that can be replaced switches when the DISC SKIP
button is pressed.
Press the open/close ( OPEN/CLOSE) button again to close the drawer.
5
Power supply outlet
A
B
AC OUTLET
Power supply outlet
TOP PAUSE P AY
EPEAT PROG
1 2 3 4
5 6 7 8
9 101 12
1 141 16
OP N O E D S
( 1 PLAY )
OPEN/CLOSE)
5
(3) SYNCHRO Jack Connections
• Connect the SYNCHRO jack with a DENON cassette deck which is
equipped with a SYNCHRO jack, then make a synchronized recording. Use
the connection cord supplied with the cassette deck.
• To make use of this function, also connect the output jacks and make the
settings so that a recording can be made from the CD player to the
cassette deck.
DCM-370/270
N OUT COAX AL
SYNCHR CONTROL DIG TAL OUT
L NE OUT
VAR ABLE
(Cassette Deck)
(2) Stopping Playback
H CD
DCM 3 0
CM UDIO T CHNOL GY / CD AUTO CH NGER RA K
RE OTE
SE SOR D SC ‚⁄ M N
¤ ‚‹ fi‚
5 DISC AUTOMATIC DISC LOADING SYSTEM
N £ OFF
P ONES
1. Press the stop button ( STOP) to stop playback.
2
2. To replace discs, press the open/close (
The disc which was playing switches over to the front side and the drawer
opens.
• Set the disc you want to
played in the front side.
CM AUD O T CHNO OGY CD AU O HAN ER DCM 370
ON £ FF
HONES
ENGLISH
Power supply outlet
STOP PA SE PLAY
REP AT P OG
1 2 3 4
SEC 5 6 7 8
9 1 1112
131 1516
PEN SE D SC KIP
( 2 STOP )
OPEN/CLOSE) button.
5
H CD
S OP PA SE LAY
REP AT PR G
RA K
1 2 3 4
E OTE
E S R I C ‚⁄ M N SEC 5 6 7 8
¤ ‚‹ fi‚ 9 1 11 2
31 15 6
PE / LO E D SC K P
5 MATIC DISC LOADING SYSTEM
9