Initial Operation - Metabo WEF 9-125 Instrucciones De Manejo

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

3.9
Special safety instructions for cordless
machines:
Remove the battery pack from the machine before
any adjustments, conversions or servicing are
performed.
Protect battery packs from water and mois-
ture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from
defective li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention imme-
diately.
SYMBOLS ON THE TOOL:
.......... Class II Construction
V ............. volts
A ............. amperes
Hz ........... hertz
.../min...... revolutions per minute
~ ............. alternating current
........... direct current
n.............. rated speed
4. Overview
See page 2.
1 Support flange
2 Spindle
3 Spindle locking button
4 Safety guard
5 Additional handle / Additional handle with vibration
damping *
6 Sliding on/off switch
7 Handle
8 Switch-on lock *
9 Trigger *
10 Electronic signal indicator *
11 Battery pack release button *
12 Capacity indicator button *
13 Capacity and signal indicator *
14 Battery pack*
15 Dust filter *
16 Clamping nut *
17 2-hole spanner *
18 Lever for safety guard attachment
* depending on equipment/not in scope of delivery

5. Initial Operation

5.1
For mains powered machines only
Before plugging in the device, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD (GFCI) with a max. trip
current of 30 mA upstream.
5.2
For cordless machines only
Dust filter
Always fit the dust filter if the surroundings are
heavily polluted (15).
The machine heats up faster when the dust
filter is fitted (15). It is protected by the elec-
tronics system from overheating (see chapter9.).
Attaching: See page 2, illustration A.
Attach dust filter (15) as shown.
To remove: Holding the dust filter (15) by the upper
edges, raise it slightly and then pull it downwards
and remove.
Rotating battery pack
See illustration B on page 2.
The rear section of the machine can be rotated 270°
in three stages, thus allowing the machine's shape
to be adapted to the working conditions. Only
operate the machine when it is in an engaged posi-
tion.
Battery pack
Charge the battery pack before use (14).
If performance diminishes, recharge the battery
pack.
The ideal storage temperature is between 10°C and
30°C.
"Li-Power" li-ion battery packs have a capacity and
signal indicator: (13)
- Press the button (12), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removing and inserting the battery pack
To remove: Press the battery pack release button
(11) and pull the battery pack (14) downwards.
To fit:Slide in the battery pack (14) until it engages.
5.3
Attaching the additional handle
Always work with the additional handle
attached (5)! Attach the additional handle on
the left or right of the machine and secure.
5.4
Install safety guard
For safety reasons, always use the safety
guard provided for the respective wheel! See
also chapter 10.
Safety guard for grinding
Designed for work with roughing wheels, flap
sanding pads, diamond cut-off wheels.
See page 2, illustration E.
- Place the safety guard (4) in the position indi-
cated.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
ENGLISH en
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Wepf 9-125Wf 18 ltx 125Wpf 18 ltx 125

Tabla de contenido