Electro Industries/GaugeTech Shark 100-S Manual De Instalación Y Operación página 95

Modbus Address
Hex Decimal
0FAF - 0FAF 4016 - 4016 Phase A Voltage 2nd harmonic magnitude
0FB0 - 0FB0 4017 - 4017 Phase A Voltage 3rd harmonic magnitude
0FB1 - 0FB8 4018 - 4025 Phase B Current harmonic magnitudes
0FB9 - 0FBC 4026 - 4029 Phase B Voltage harmonic magnitude
0FBD - 0FC4 4030 - 4037 Phase C Current harmonic magnitudes
0FC5 - 0FC8 4038 - 4041 Phase C Voltage harmonic magnitude
14
Phase Angle Block
1003 - 1003 4100 - 4100 Phase A Current
1004 - 1004 4101 - 4101 Phase B Current
1005 - 1005 4102 - 4102 Phase C Current
1006 - 1006 4103 - 4103 Angle, Volts A-B
1007 - 1007 4104 - 4104 Angle, Volts B-C
1008 - 1008 4105 - 4105 Angle, Volts C-A
Status Block
1387 - 1387 5000 - 5000 Meter Status
1388 - 1388 5001 - 5001
Limits Status
1389 - 138A 5002 - 5003 Time Since Reset
9
Resets Block
4E1F - 4E1F 20000 - 20000 Reset Max/Min Blocks
4E20 - 4E20 20001 - 20001 Reset Energy Accumulators
Meter Programming Block
55EF - 55EF 22000 - 22000 Initiate Programmable Settings Update
55F0 - 55F0 22001 - 22001 Terminate Programmable Settings Update
e
Electro Industries/GaugeTech
1
Description
7
Commands Section
3
6
Format Range
UINT16 0 to 65535 none
UINT16 0 to 65535 none
same as Phase A Current 0th to 7th harmonic magnitudes
same as Phase A Voltage 0th to 3rd harmonic magnitudes
same as Phase A Current 0th to 7th harmonic magnitudes
same as Phase A Voltage 0th to 3rd harmonic magnitudes
SINT16 -1800 to +1800 0.1 degree
SINT16 -1800 to +1800 0.1 degree
SINT16 -1800 to +1800 0.1 degree
SINT16 -1800 to +1800 0.1 degree
SINT16 -1800 to +1800 0.1 degree
SINT16 -1800 to +1800 0.1 degree
--exnpch ssssssss
UINT16 bit-mapped
UINT16 bit-mapped 87654321 87654321
UINT32 0 to 4294967294 4 msec
4
5
UINT16
password
5
UINT16
password
5
UINT16
password
UINT16 any value
Doc# ES145721
Units or
Resolution Comments
exnpch = EEPROM block OK flags
(e=energy, x=max, n=min, p=programmable
settings, c=calibration, h=header),
ssssssss = state (1=Run, 2=Limp, 10=Prog
Set Update via buttons, 11=Prog Set
Update via IrDA, 12=Prog Set Update via
COM2)
high byte is setpt 1, 0=in, 1=out
low byte is setpt 2, 0=in, 1=out
wraps around after max coun
meter enters PS update mode
meter leaves PS update mode via reset
#
Reg
1
1
8
4
8
4
Block Size:
42
read-only
1
1
1
1
1
1
Block Size:
6
read-only
1
1
2
Block Size:
4
write-only
1
1
Block Size:
2
read/conditional write
1
1
MM-4