LEGRAND Wattstopper EOSW-101 Instrucciones De Instalación

No: 24267 – 08/16 rev. 1
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: EOSW-101,EOSW-102
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
EOSW-101
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The EOSW-101 and EOSW-102 Wall Switch Receivers are a one or two button switch that replaces a standard wall switch. It is the only
wired component of the system. The EOSW receivers receive signals from the Occupancy Sensor (EOPC) via radio frequency once
they are paired to the occupancy sensor.
NOTE: Pairing of devices should be done prior to binding and configurating loads. Pairing refers to establishing a link between two or
more devices for communication purposes. Binding refers to assigning a load to a specific button on a load controlling device
such as an EOSW. Please refer to the EOPC-100 Installation Instructions for PAIRING of sensor to EOSW-101/102 receivers.
Please refer to the EORS-10x/EOHR-10x Installation Instructions for PAIRING of the remote or handheld switches to the
EOSW-101/102 receivers.
Time Delay: Three Green Time Delay LEDs on the left-side of
the switch display the selected time delay value of 30, 15 or 5
minutes. When a LED is ON, its corresponded value is active.
Each tap of the 'T' button cycles through the values.
Operating Mode: Two Green Operating Mode LEDs display the
selected operating mode. Each tap of the 'O' button alternates
between "Manual-On (M)" and "Automatic-On (A)".
Load Status: Each Load (Switch) Button has a Blue load status
LED. The LED is solid ON when the load paired to that button is
turned ON, and DIM when the load is OFF. Tap a Load (Switch)
Button to toggle loads ON/OFF.
Pairing Mode: One Green Pairing LED displays when in Pairing
mode. Each tap of the 'P' button cycles through the loads.
Configuration: Tap the 'C' button to enter configuration mode
and set load parameters on the receiver and assign buttons to
loads.
Air Gap Button: Press down to activate. Press the Air Gap Release button (left side) to deactivate.
Wattstopper
Wireless Lighting Control System EOSW Series Wall Switch Receivers
Système de contrôle de l'éclairage sans fil Récepteurs interrupteurs
muraux de la série EOSW
Sistema de control de iluminación inalámbrico Receptores con
interruptor de pared serie EOSW
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
EOSW-102
OPERATION
BUTTONS AND LED INDICATORS
Green Time Delay
LEDs (3)
Time Delay Button
Green Operating
Mode LEDs (2)
Operating Mode Button
®
SPECIFICATIONS
Input Voltage: ............................................ 120/277 VAC, 60 Hz
Load: ........................................................ 800W ballast @120V,
1200W fluorescent @277, 15W minimum for 120 VAC/60Hz,
30W minimum for 277 VAC/60Hz, LED driver, ELV, MLV, 1/6 HP
Time delay: ............................................ 5-30 minute adjustable
Connection to Wireless Network: ...............................................
Receives signals from Wireless Ceiling Sensor
(EOPC) and Remote Switch (EORS) via Radio Frequency
Environment ................................................For Indoor Use Only
Operating Temperature ................... 32° to 104°F (0° to 40°C)
Storage Temperature......................23° to 176°F (-5° to 80°C)
Relative Humidity ......................... 5 to 95% (non condensing)
Patent Pending
EOSW-101 Series
Air Gap Release
Button
1 Load Button Switch
EOSW-102 Series
Blue Load Status
LEDs
Load Button
Green Pairing LED
Pairing Button
Load Button
Configuration Button
Air Gap Button
2 Load Button Switches