Denon Professional DN-V200 Instrucciones De Operación página 48

ENGLISH
Use the • and ª cursor buttons to select the MP3 file you want to play,
then press the PLAY or ENTER button.
• Playback starts.
The display can be switched between the single elapsed time and the
single remaining time by pressing the DISPLAY button.
Programmed playback is not possible with MP3 discs.
To change the MP3 file
Press the STOP button, then use the • and ª cursor buttons to
reselect the desired MP3 file.
To set the random play mode
(Also refer to " Special play modes for MP3 and JPEG files " on page
50.)
3
In the stop mode, press the RANDOM button.
Then press the PLAY or ENTER button.
To set the repeat mode
(Also refer to " Special play modes for MP3 and JPEG files " on page
50.)
The repeat mode changes each time the REPEAT button is pressed.
To return to the initial disc information screen
Press the STOP button, use the • cursor button to select "ROOT" at
the upper right of the screen, then press the ENTER button.
The screen in step 1 reappears.
NOTES:
• The DN-V200/DN-V300 is compatible with the "MPEG-1 Audio Layer 3" standards (sampling frequency of 32, 44.1 or 48 kHz). It
is not compatible with such other standards as "MPEG-2 Audio Layer 3", "MPEG-2.5 Audio Layer 3", MP1, MP2, etc.
• It may not be possible to play some CD-R/RW discs due to disc properties, dirt, warping, etc.
• The digital signals output when playing MP3 files are MP3 signals converted into PCM, regardless of whether the audio output
presetting is set to "normal" or "PCM". The signals are output with the same sampling frequency as that of the music source.
• In general, the higher an MP3 file's bit rate, the better the sound quality. On the DN-V200/DN-V300, we recommend using MP3
files recorded with bit rates of 128 kbps or greater.
• MP3 files may not be played in the expected order, since the writing software may change the position of the folders and the
order of the files when writing them on the CD-R/RW.
• Programmed playback is not possible with MP3 discs.
• When writing MP3 files on CD-R/RW discs, select "ISO9660 level 1" as the writing software format. This may not be possible
with some types of writing software. For details, refer to the writing software's usage instructions.
• With the DN-V200/DN-V300 it is possible to display folder names and file names on the screen like titles. The DN-V200/DN-V300
can display up to 8 characters, consisting of numbers, capital letters, and the "_" (underscore) mark.
• If recorded in a format other than "ISO9660 level 1", normal display and playback may not be possible. In addition, folder and file
names including other symbols will not be displayed properly.
• Be sure to add the extension ".MP3" to MP3 files. Files cannot be played if they have any extension other than ".MP3" or if they
have no extension. (with Macintosh computers, MP3 files can be played by adding the extension ".MP3" after the file name
consisting of up to 8 capital or numbers and recording the files on the CD-R/RW.)
• Do not apply stickers, tape, etc., to either the label side or the signal side of CD-R/RW discs. If adhesive gets on the surface of
a disc, the disc may get stuck inside the DN-V200/DN-V300 and be impossible to eject.
• The DN-V200/DN-V300 is not compatible with packet write software.
• The DN-V200/DN-V300 is not compatible with ID3-Tag.
• The DN-V200/DN-V300 is not compatible with play lists.
• Do not play CD-R/RW discs containing any files other than music CD files (in CDA format), MP3 and JPEG files. Doing so may
result in malfunction or damage, depending on the type of file.
48
FOLDER FOLDER REPEAT
TRACK REPEAT DISC REPEAT
Remote control unit
DISC
ENTER
Remote control unit
Main unit Remote control unit
FOLDER
PLAY MODE:
ROOT --
F OL DER 1
MP3_01
F OL DER 2
MP3_02
F OL DER 3
MP3_03
F OL DER 4
MP3_04
F OL DER 5
MP3_05
SINGLE ELAPSED
-- : --
0
1
2
3
4
5