Evolution RAGE230 Instrucciones Originales página 5

iNTENDED uSE
Symbol Description
OF ThiS POwER TOOL
V
Volts
wARNiNG: This product is a Hand Operated
Circular Saw and has been designed to be
used with special Evolution blades. Only use
A
Amperes
accessories designed for use in this machine
and/or those recommended specifically
by Evolution Power Tools Ltd.
Hz Hertz
When fitted with an appropriate blade
Min -1 Speed this machine can be used to cut:
Mild Steel
~ Alternating Current
Aluminium
wood
n o No Load Speed
PROhiBiTED uSE OF ThiS POwER TOOL
wARNiNG: This product is a Hand Operated
Wear Safety Goggles
Circular Saw and must only be used as such.
It must not be modified in any way, or used to
power any other equipment or drive any other
Wear Ear Protection
accessories other than those mentioned in this
Instruction Manual.
Wear Dust Protection
wARNiNG: This machine is not intended
for use by persons (including children) with
Read Instructions reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless
they have been given supervision or instruction
CE Certification
concerning the safe use of the machine by a
person responsible for their safety and who is
competent in its safe use.
CSA Certification
Children should be supervised to ensure
that they do not have access to, and are not
Waste Electrical &
allowed to play with, this machine.
Electronic Equipment
Warning
8
www.evolutionpowertools.com www.evolutionpowertools.com
ELECTRiCAL SAFETy
This machine is fitted with the correct
moulded plug and mains lead for the
designated market. If the mains lead or the
plug are damaged in any way, they must be
replaced with original replacement parts by a
competent technician.
OuTDOOR uSE
wARNiNG: For your protection, if this tool
is to be used outdoors it should not be
exposed to rain or used in damp locations.
Do not place the tool on damp surfaces.
Use a clean, dry workbench if available. For
added protection use a residual current
device (R.C.D.) that will interrupt the supply
if the leakage current to earth exceeds 30mA
for 30ms. Always check the operation of the
residual current device (R.C.D.) before using
the machine.
If an extension cable is required it must be a
suitable type for use outdoors and so labelled.
The manufacturer's instructions should be
followed when using an extension cable.
POwER TOOL GENERAL
SAFETy iNSTRuCTiONS
(These General Power Tool Safety Instructions
are as specified in BS EN 60745-1:2009
& EN 61029-1:2009).
wARNiNG: Read all safety warnings and
instructions. Failure to follow the warnings
and instructions may result in electric shock,
fire and/ or serious injury.
Save all warnings and instructions for
future reference. The term "power tool" in
the warnings refers to your mains-operated
(corded) power tool or battery-operated
(cordless) power tool.
9
1) General Power Tool Safety warnings
[work area safety]
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gasses or dust. Power
tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away
while operating power tool. Distractions
can cause you to lose control.
2) General Power Tool Safety warnings
[Electrical Safety]
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
b) Avoid body contact with earthed
or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body
is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) when operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) if operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
EN
ES
FR
NL