Technical Data; Noise Emission Levels; Before Using For The First Time; Assembly And Operation - EINHELL TPR 200/1 Manual De Instrucciones

Anl. TPR 200_1 30.03.2004 13:53 Uhr
Replace immediately.
Never use segmented cutting wheels.
Caution! The cutting wheel runs on after the
machine is switched off!
Never apply side pressure to the diamond cutting
wheel in order to bring it to a halt.
Caution! The diamond cutting wheel must be
cooled with water at all times.
Always pull out the power plug before changing
the cutting wheel.
Use only suitable diamond cutting wheels.
Never leave the machine unattended in rooms
with children.
Always pull out the power plug before examining
the electric motor compartment system.

5. Technical data

Motor rating
Motor speed
A.c. motor
Insulation material class
Insulation
Cut length
Jolly length
Cut height 90°
Cut height 45°
Cutting table:
Dimensions
Diamond cutting wheel

Noise emission levels

The noise emitted by this saw is measured in
accordance with EN ISO 3744; EN ISO 11201
The noise at the workplace may exceed 85 db
(A). The user will require noise protection
measures if this is the case. (Wear ear-muffs!)
With-load
operation
Sound pressure level 72.2 dB(A)
Sound power level 85.2 dB(A)

6. Before using for the first time

The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench, the base frame supplied in delivery, or
similar.
All covers and safety devices must be correctly
attached before the machine is used for the first
time.
The cutting wheel must rotate smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.

7. Assembly and operation

7.1 Assembly of the base frame and cooling
water pump (Fig. 2-4)
Fasten the feet (18) to the base frame (12) with
the screws (19).
Turn the base frame upright (see Fig. 5).
Place the trough (3) in the base frame (12).
Place the cooling water pump (13) in the trough
(3).
Fill with water until the pump (13) is full.
Place the complete tile cutting machine in the
trough (3) (see Fig. 2).
800 W
Unscrew the star grip screw (11) (for securing
2950 rpm
during transportation!).
230 V ~ 50 Hz
7.2 ON/OFF switch (Fig. 6)
Class B
IP54
To switch on, press the "1" on the ON/OFF
switch (16).
520 mm
Before you begin cutting, wait until the cutting
520 mm
wheel has reached maximum speed and the
max. 30 mm
cooling water pump (13) has started supplying
max. 25 mm
the cutting wheel with water.
To switch off, press the "0" on the switch (16).
790 x 395 mm
7.3 90° Cutting (Fig. 7/8)
ø 200 x ø 25.4
Loosen the star grip screw (27).
Set the angle stop (5) to 90° and retighten the
star grip screw (27).
Retighten the screws (28) to fasten the angle
stop (5).
Move the machine head (29) to the far end with
the handle (9).
Position the tile against the rail fence (6) on the
angle stop (5).
No-Load
Switch on the tile cutting machine.
operation
Caution: Always wait until the cooling water has
60.6 dB(A)
reached the cutting wheel (2) first.
73.6 dB(A)
Move the machine head (29) slowly and
smoothly forward through the tile with the handle
(9).
Switch off the tile cutting machine after
completion of cutting.
7.4 45° Diagonal cut (Fig. 9)
Set the angle stop (5) to 45°.
Cut as described in 7.3.
Seite 9
GB
9