Disposal Of Household Appliances; Installing The Appliance - BORETTI Beermachine Manual De Instrucciones

4.

DISPOSAL OF HOUSEHOLD APPLIANCES

Under the European directive 2002/96/EC on waste from electrical and electronic equipment (WEEE),
household appliances may not be disposed of at normal landfi ll sites. Old appliances must be collected separately to optimise the recovery and recycling of their
materials and to prevent potential harm to health and the environment. The symbol of a bin with a cross is affi xed on all products, to remind users that
they must dispose of the product separately. For further information on how to dispose of household appliances, users should contact a public authority or their
dealers.
CE This appliance has been manufactured in compliance with EN 60204 –1 ; and conforms to the
directives: -98/37/EG -89/336/EWG EMV -73/23/ EWG
5.

INSTALLING THE APPLIANCE

(fi g. 2)
Make sure the beer dispenser can fi t into the cabinet (fi g 2).
1. Drill a Ø 5 cm hole at the back of the cabinet base (fi g. 2) to pass the beer fl ow line through (fi g. 2).
2. Position the dispenser, after connecting the mains lead and passing the beer fl ow line "G" (fi g. 2) through the cabinet base (where the keg is stored) (fi g
2).
3. Secure the dispenser to the base using the 2 screws provided, inserted in the two holes in the drip tray storage area.
4. Fit the tray and rack.
5. Fit the control unit on the side of the cabinet, placing it against the base and secure with the 4 screws provided (fi g. 2).
6. Insert the adaptor (same type as the dispense head) in the washing attachment.
7. Carefully connect fi tting "H" (fi g. 1), positioned at the end of the beer fl ow line "G" (fi g. 1) to the beer outlet connection of the dispense head "I" (fi g.
1).
8. Carefully connect fi tting "K" (fi g. 1) , positioned at the end of the CO² fl ow line "M" (fi g. 1) to the CO² inlet connection of the dispense head "I" (fi g. 1).
9. Fit the dispense head on the keg attachment and secure lowering the dispense head lever and making sure it is fi tted properly to avoid beer and CO² leaks.
Click to secure.
* Important: 2 different kinds of dispense heads are supplied with this appliance, which together are compatible for most kegs of beer. Benath you fi nd a
short description for both kinds of dispense heads:
1 Korb or S-System: compatible for most kinds of beer, including Heineken™, Amstel™, Dommelsch™, Hertog Jan™, Jupiler™, Stella Artois™, Fischer™,
Adelscott™, Despérados™, Beck's™, Leffe™, Boomerang™, Loburg™, Hoegaarden™, Kilkenny™, Spaten™, La Bécasse™, Pelford™, Affl ingem™, George
Killians™, Maes™, Haacht™, Britt™, Löwenbräu™, Mousseol™, Labatt™, Bass™, Diekirch™, Belle-Vue™, Dafi r™, Julius™
2 Flach or A –System: compatible for Beers including. Warsteiner™, Grolsch™, Dommelsch 20™, Palm™, Grimbergen™, San Miguel™, Kronenbourg™,
Kanterbrau™, Brugs™, Beamish Red™, Beamish Stout™, Gilbert™, Wel Scotch™, Wilford™, Foster™
Boretti BV shall not be held liable in any way for fl aws regarding the above information, or changes made to the keg connections by certain beer brewers.
Always ask your keg retailer if a certain keg is compatible for either a Korb (S-System) or Flach (A-System) connection.
14
G
3 4
562
2 EN 5
1 O 6
0,5 MICR C
0 MATI
bar
IC
RO MAT
MIC
150
100
N 562 200
E
50
MICRO MATIC 250
20
bar
20
568
400
550
350
595
19
IC41