Synchronising Bft Rolling Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

permission.
3. After 10 seconds the receiver will exit synchronisation mode
and emit 2 short beeps.
SYNCHRONISING APRIMATIC ROLLING CODE REMOTE
CONTROLS
Direct synchronisation procedure on the receiver
1. Open the receiver and locate a switch or pushbutton labelled
"PROG".
2. Press the button or turn on the switch.
The receiver will emit a long beep and the LED will light up.
From this point, follow the previous procedure from step 2
above.
Synchronising the APRIMATIC TR remote control
1. Stand near the receiver and press all the emission keys of the
device already synchronised in the facility.
The receiver will emit a continuous beep.
2. Press the synch button of the duplicated device.
3. Then press any key of the duplicated device.
The LED and buzzer will pause briefly and then resume, confir-
ming that the remote control is now synchronised.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING APRIMATIC TXM ROLLING CODE RE-
MOTE CONTROLS
Remote synchronisation procedure for the APRIMATIC TXM
remote control
1. Stand near the receiver and press all the emission keys of the
device already synchronised in the facility.
The receiver will emit a beep and the LED will flash.
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a mo-
ment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press
the synch or copy button of the original or duplicated remote
control.
The LED and buzzer will turn off.
Direct synchronisation procedure for the APRIMATIC TXM re-
mote control
1. Open the receiver and press the small button located near
the LED for 2 seconds.
The receiver LED will flash
2. Press the synch button of the duplicated device.
The beep will pause and the LED will remain steady for a mo-
ment to confirm that it has received the valid code.
3. Wait 30 seconds to exit the synchronisation mode or press
the synch or copy button of the master remote control.
The LED and buzzer will turn off.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
22
SYNCHRONISING BENINCA ROLLING CODE REMOTE
CONTROLS
Remote synchronisation procedure for the BENINCA remote
control
1. Stand near the receiver and press the already synchronised
hidden transmitter key.
2. Within 5 seconds press the key on the already synchronised
remote control that corresponds to the channel to be associa-
ted with the new device.
3. Within 5 seconds, press the key of the new device to be
associated with the channel selected in step 2.
The receiver will memorise the new transmitter and exit syn-
chronisation mode immediately.
Direct synchronisation procedure for the BENINCA remote con-
trol
1. Open the receiver and briefly press the P button.
The red LED on the receiver will light up for 3 seconds, turn off
for 1 second and light up for a further 5 seconds.
2. While the red LED is lit up, press the transmitter button that
you want to synchronise with channel 1.
Other transmitters can also be entered. You only have to press
a key before 5 seconds elapse since the previous device was
synchronised.
3. Once finished, wait 5 seconds until the receiver exits syn-
chronisation mode.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING BFT ROLLING CODE REMOTE CON-
TROLS
The receivers of these models enable remote or direct synchro-
nisation.
Remote synchronisation procedure for the BFT MITTO remote
control
1.
Stand near the receiver and press the hidden button at the
rear of the BFT original remote control for 2 seconds.
2. Press the left button on the front of the original remote con-
trol for 2 seconds.
3.
Press the synch button on the rear of the device to be syn-
chronised.
4. Finally, press the first button on the device to be synchro-
nised.
Remote synchronisation procedure for the BFT TRC or MITTO
remote control
1. Open the receiver and locate the SW-1 and SW-2 buttons.
Press the first (SW-1).
A flashing LED should light up in the receiver.
2. Open the battery cover of the already synchronised remote
control or the one you have copied and press the button inside.
The receiver light should change to steady.
3. Press the button of the device to be synchronised.
The light on the receiver will return to flashing and turn off
after 30 seconds, indicating that the synchronisation process
has finished.
Observations