Synchronising Key Rolling Code Remote Con- Trols; Synchronising Mutancode Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

SYNCHRONISING KEY ROLLING CODE REMOTE CON-
TROLS
KEY remote controls can only be synchronised directly on the
receiver.
Direct synchronisation procedure on the receiver (type A recei-
ver)
1. Press button S on the receiver.
2. The LED (Ir1) will light up.
3. Release button S and press button P.
4. The LED (Ir1) will flash once.
5. Release the button.
6. Press the button of the remote control to be synchronised
until the LED (Ir1) begins to flash, then release.
7. Wait for 10 seconds for the receiver to exit synchronisation
mode.
Direct synchronisation procedure on the receiver (type B recei-
ver)
1. Press KEY the same number of times as the channel you wish
to synchronise (one time for channel 1, two times for channel
2, etc.).
2. The LED will flash the number of times equal to the number
of the selected channel.
3. Within the next 7 seconds, press the button on the remote
control to be synchronised for 2 seconds.
4. The LED will flash once if synchronisation has been success-
ful.
5. Repeat step 3 if you wish to add more remote controls.
SYNCHRONISING LIFT MASTER ROLLING CODE REMO-
TE CONTROLS
The Lift Master remote control can only be synchronised direct-
ly on the receiver.
Direct synchronisation procedure on the receiver
1. Press the button on the remote control and hold.
2. Press and release the Learn button for channel A on the re-
ceiver.
3. The control LED will flash once.
4. Release the remote control button.
If you release the remote control button before the control LED
flashes the receiver will not accept the code.
Repeat this procedure for any other devices you wish to add.
If you are using a second door, select another button on the
remote control and repeat the steps for channel B.
SYNCHRONISING MHOUSE ROLLING CODE REMOTE
CONTROLS
MHOUSE remote controls can be synchronised either directly
on the receiver or remotely using a remote control already syn-
chronised with the receiver.
Remote synchronisation procedure (identical to procedure for
NICE, Smilo and Flo-R devices)
1. Press and hold the button on the device you wish to synchro-
nise for at least 5 seconds and then release.
2. Slowly press the button on the previously-synchronised re-
mote control 3 times.
3. Slowly press the button on the device to be synchronised
once.
Direct synchronisation procedure on the receiver
1. Press button P1 on the receiver and hold for at least 3 se-
conds.
2. Release the button when LED P1 lights up.
3. You have 10 seconds to press any button on the device to be
synchronised for at least 2 seconds. LED P1 will flash 3 times if
synchronisation has been performed successfully.
4. If you wish to synchronise additional remote controls, repeat
step 2 within 10 seconds or the receiver will automatically exit
synchronisation mode.
SYNCHRONISING MOTORLINE ROLLING CODE REMOTE
CONTROLS
MOTORLINE remote controls can only be synchronised directly,
using the following procedure.
Synchronisation procedure on the receiver
" "
1. Press the SEL button repeatedly until the LED marked
" "
CODE lights up steady.
2. Press the button on the remote control to be synchronised.
3. After a while the LED will turn off and the remote control will
then be synchronised.
SYNCHRONISING MUTANCODE CODE REMOTE CON-
TROLS
Mutancode remote control receivers enable remote synchroni-
sation without handling the receiver or using the button on its
circuit board.
Remote synchronising procedure
1. Stand near the receiver, open the battery cover on the ori-
ginal remote control and press the button next to the battery.
The receiver should emit two beeps, indicating that it has ente-
red synchronisation mode.
If not, repeat step one. If the receiver still fails to emit the
beeps the remote synchronisation option may be disabled. Try
using the direct synchronisation procedure.
Take the following steps if the receiver has emitted 2 beeps:
2. Within 30 seconds of the beeps, press the button on the de-
vice to be synchronised.
The receiver will then emit a short beep, indicating that the
device has been successfully synchronised.
If the receiver fails to emit the short beep it may mean that the
memory is full and the remote control cannot be synchronised
without the installer's permission.
3. Wait for 30 seconds until the receiver has exited synchro-
nisation mode.
Once all the above steps have been performed correctly, test
the new remote control by opening and closing the doors.
Direct synchronisation procedure on the receiver
1. The receiver button may be on one side of the casing or insi-
de on the circuit board.
2. Press the button on the circuit board.
The receiver should emit two beeps, indicating that it has ente-
red synchronisation mode. From this point, follow the previous
procedure from step 2 above.
SYNCHRONISING NICE ROLLING CODE REMOTE CON-
TROLS
27