Synchronising Seav Rolling Code Remote Con- Trols; Synchronising Somfy Rolling Code Remote Con- Trols - JMA M-FR1 Manual De Instrucciones

(channel) transmits a different code.
a. The LED flashes slowly during synchronisation and remains
steady once the operation has been successfully concluded.
b. If a LED begins to flash quickly, it means that this channel
has already been synchronised and associated with the LED
concerned. Repeat the operation to change allocation of the
relay prior to the one currently selected.
c. If all the LEDS flash at once it means that the memory is full.
The code has not been stored.
5. Repeat the operation for all buttons (channels) you wish to
synchronise, always selecting the relay to which they are to
be associated.
6. Repeat the operation for all the remote controls you wish
to synchronise.
7. Press ENTER RADIO again to exit synchronisation mode. The
LEDS will turn off. The device will exit synchronisation mode
automatically 10 seconds after the last operation.
8. The codes are stored and will not be deleted even in the
event of a power cut.
SYNCHRONISING ROPER ROLLING CODE REMOTE CON-
TROLS
This receiver does not usually include the remote synchroni-
sation option. Therefore the direct method using the receiver
is recommended. Notwithstanding, both procedures are exp-
lained below.
Remote synchronisation (option not normally enabled)
1. Stand near the receiver and use a pointed object to press
the pushbutton at the rear of the synchronised remote control.
The receiver will emit a beep, indicating that it has switched to
synchronisation mode.
2. Within 10 seconds of the beep, press the button on the devi-
ce to be synchronised.
The receiver will emit another short beep to indicate that the
remote control has been synchronised.
If the receiver fails to synchronise the device, it may mean that
the memory is full and the remote control cannot be synchroni-
sed without the installer's permission.
3. After 10 seconds the receiver will exit synchronisation mode
and emit 3 short beeps.
Direct synchronisation procedure on the receiver
1.
Open the ROPER receiver.
2. Locate a small button marked PROG/RES.
3. Press the button and hold for one or two seconds until the
receiver emits a beep.
The receiver emits a beep
4. Release the receiver button and press the button on the re-
mote control to be synchronised. If you wish to synchronise ad-
ditional remote controls, press the buttons of each one in turn.
The receiver will emit a beep every time a remote control is sy-
nchronised, indicating that the operation has been successful.
5. Wait for 10 seconds after finishing.
The receiver will emit a beep, indicating that it has exited the
synchronisation mode.
SYNCHRONISING SEAV ROLLING CODE REMOTE CON-
TROLS
Remote synchronisation procedure for the SEAV remote control
1. Stand near the receiver and press the first desired channel
on the already synchronised remote control for 15 seconds.
The receiver LED will begin to flash while it is waiting for trans-
mission of a code.
2. Press the button for the same channel on the remote control
to be synchronised.
The receiver LED will light up steady, indicating that the chan-
nel has been synchronised.
Repeat the operation for the remaining buttons.
Direct synchronisation procedure for the SEAV remote control
1. Open the receiver and press the button marked SEL.
The CODE CH1 LED will begin to flash while it is waiting for
transmission of a code.
2. Press the button for the same channel on the remote control
to be synchronised.
The receiver LED will light up steady, indicating that the chan-
nel has been synchronised.
Repeat the same process for the second channel but pressing
the SEL button twice (the CODE CH2 LED will flash) and pres-
sing the second button on the duplicated device.
Observations
If the procedure fails, it may mean that the receiver memory is
full and impedes synchronisation of new devices without the
installer's permission.
SYNCHRONISING SKYMASTER ROLLING CODE REMOTE
CONTROLS
SKYMASTER remote controls can only be synchronised directly
on the receiver. The process is as follows.
Synchronisation procedure on the receiver
1. Press the CODE button once.
The red LED will begin the flash.
2. Press the button on the remote control to be synchronised
twice.
The red LED will change to steady and then turn off.
3. Repeat the operation for every button (channel) and every
device you wish to synchronise.
If the remote control being synchronised is the first one, you
will have to delete the memory as follows:
1. Press and hold the CODE button for 8 seconds during which
the LED will remain steady.
2. The red LED will turn of and the memory will be deleted.
SYNCHRONISING SOMFY ROLLING CODE REMOTE CON-
TROLS
SOMFY remote control can only be synchronised directly on the
external receiver and remotely on the integrated shutter recei-
ver. A distinction must be made between SOMFY and TELIS
remote controls.
Synchronisation procedure on the receiver
External receiver
1. Press and hold the "Prog" button on the receiver for 2 se-
conds. The red LED on the receiver will remain lit.
Internal receiver (Telis)
29