Publicidad
Idiomas disponibles
Idiomas disponibles
TIMER
SHIFT
The unit can be turned on at a specified
time every day with the
built-in timer.
Preparation
Make sure the clock is set correctly,
1 Press one of the function
buttons to select a
source.
If
"WNER/BAND
is pressed,
the band cannot be selected
in
this step.
2 Press TIMER repeatedly until @ appears on the
display.
When using the remote control,
press
TIMER while
pressing
SHIFT.
Time and audio source name flash alternately.
3 Mhin
6 seconds, turn MULTI JOG to designate
the timer-on time, then press ENTER or Il.
Turning MULTI JOG changes
both the hour and the minute.
++
or ~
is also available
instead of MULTI JOG. Holding
these buttons down will vary the time rapidly,
4 Mhin
4 seconds, turn MULTI JOG to select the
duration for the timer-activated
period.
The duration
can be set between
5 and 240 minutes
in 5-
minute steps.
+1
or *
is also available
instead of
MULTI JOG.
5
6
7
Adjust the volume.
I%
The source sound will play at the volume level set in this step
~
when the power is turned on by the timer.
~=~
If the volume
level is set to 21 or higher,
however,
it will
~$'?.t
automatically
be set to 20 when the power is turned
on.
:$" @
~:.>. , :- ,>,~
Prepare the source.
~t;i
#
.!*.
To listen to a CD,
load the disc to be played first on tray 1,
'~ #
To listen to a tape,
insert the tape into deck 1 or 2.
#
To listen to the radio,
tune in to a station.
6
Press POWER to turn off the power.
When the timer-on
time is reached;
the unit turns on and
begins play with the selected
source.
m
You can change the source that was selected in step 1 by pressing
one of the function
buttons before pressing
ENTER
or II in step
3.
To
check the timer setting
Press
TIMER,
The
selected
source, the timer-on
time, and the duration
nor the
timer-activated
period will be displayed
for 4 seconds.
To
change any of the previous setting
Carry out from step 1.
However,
if you do not change
the timer-on
time, in step 3 just
press
ENTER
twice and continue
from step 4.
To
cancel the timer standby mode temporarily
Press
TIMER
repeatedly
so that @ disatmears.
To restore the timer standby
mode, pre:;s again to display @.
Using the unit while the timer is set
You can use the unit normallv
after settina the timer.
Before turning off the power, "carry out st;p 5 and 6.
m
Timer playback
and timer recording
will not begin unless the
power is turned off.
Connected
equipment
cannot be turned on and off by the built-
in timer of this unit, Use an external
timer.
Timer recording
is applicable
for TUNER
and VI DEO/AUX
(with
an external
timer) sources
only,
Press either
TUNER/BAND
or
VIDEO/AUX
to select a source,
then
press TIMER repeatedly until @REC lights up on the
display.
Within
6 seconds,
carry out the steps of "SETTING
THE TIMER" from step 3 and insert the tape to be recorded
on
into deck 2 after step 6.
When the power-economizing
mode (page 7) has been turned
on, the timer recording
volume
level will be O (minimum
level).
You cannot use the timer function
to record from a CD or tape,
The duration
will be automatically
set after 4 seconds.
It will
alsc, be set if
ENTER
or 11 is pressed
within 4 seconds
after
step 4.
ENGLISH
27
Publicidad
