Denon DRR-M33 Instrucciones De Operación página 12

ENGLISH
(5) Synchronized recording (when connected to RCD-M33/M35DAB)
2 When the DRR-M33 is set to the recording pause mode, recording starts automatically when the
(play/pause) button on the CD receiver is pressed.
RCD-M33/M35DAB
3
(CD receiver)
1
2
DRR-M33 (this unit)
7 6 4
RC-999 (System remote control unit)
1
8
12
8
Turn on the power of
1
the CD receiver.
(RCD-M33/M35DAB) (RC-999)
Load the cassette tape onto which
2 you want to record into the DRR-
M33's cassette holder.
3
Make the CD receiver settings.
Set the DRR-M33's play direction
4 indicator ( 0 or 1 ) to the direction
in which you want to record.
Set the reverse mode.
5
5
Refer to page 7.
6
Set the Dolby NR mode.
Press the DRR-M33's REC button
7
once to set the recording pause
mode.
Press the 1 / 3
(play/pause) button on
the CD receiver.
(RCD-M33/M35DAB)
8
• Recording starts automatically.
• When playback on the CD receiver ends,
the CD receiver is automatically set to the
stop mode and the DRR-M33 is set to the
recording pause mode.
To stop recording in the middle, press the
(stop) button on the CD receiver to stop
playback of the CD.
(6) Timer functions (when connected to the RCD-M33/M35DAB)
2 The timer functions of the CD receiver (RCD-M33/M35DAB) can be used to play cassette tapes or record
1 / 3
radio programs ("Air Check") at set times.
• Refer to the operating instruction included with the RCD-M33/M35DAB.
(7) Editing functions (when connected to the RCD-M33/M35DAB)
2 Use this function to automatically edit the tracks on the CD to fit on the tape to be used for recording.
2 The editing function is set from system remote control unit included with the CD receiver (RCD-M33/M35DAB).
RCD-M33/M35DAB
3
(CD receiver)
(DRR-M33)
1
(DRR-M33)
DRR-M33
2
(this unit)
(DRR-M33)
RC-999 (System remote control unit)
(DRR-M33)
(DRR-M33)
NOTES:
• The editing function will not work with discs containing more than 26 tracks.
• Load the cassette tape onto which you want to record into the cassette deck's cassette tray with side A
facing up before starting edited recording. The beginning of the tape is automatically found before
recording starts.
(RC-999)
• When using a recorded cassette tape for edited recording, recording stops and a blank section is left on
side B of the tape if the tape is longer than the set time, so erase the tape beforehand.
• When the editing function is used for recording, set the REVERSE MODE switch to
possible to record on side B after side A.
• In some cases it may not be possible to record all the tracks on the disc, even if the tape is longer than
the disc's recorded time (because of how the tracks are divided onto sides A and B of the tape). The
2
"OVER" indicator on the CD receiver flashes if there are tracks that cannot be recorded.
• REC button, 6 7 button, CD SRS button,
function during editing.
• To cancel the editing mode, press the
of the CD. The editing mode is not canceled if other buttons are pressed.
3
Turn on the power of
1
the CD receiver.
(RCD-M33/M35DAB) (RC-999)
Load the cassette tape onto which
2
you want to record into the DRR-
M33's cassette holder.
2
3 Load the CD into the CD receiver.
Now operate as described in the "Editing
Function" section
4
instructions included with the CD receiver
(RCD-M33/M35DAB).
1
0 1 (direction) button and 5 (open/close) button will not
2 (stop) button on the DRR-M33 or the CD receiver to stop playback
(DRR-M33)
(RCD-M33/M35DAB)
of the operating
if not, it is not