Electrical Safety; Using Your Machine - Black and Decker MTE912 Manual De Instrucciones

m ) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
n ) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
o ) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
p ) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of these
devices can reduce dust related hazards.
Power Tool Use and Care
q ) a. Do not force the power tool. Use the correct
power tool for your application. The correct power
tool will do the job better and safer at the rate for
which it was designed.
r ) b. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
s ) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
t ) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
u ) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Service
v ) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

Electrical Safety

Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.

WARNING! If the power cord is damaged,
it must be replaced by the manufacturer,
authorized BLACK+DECKER Service Center or
an equally qualified person in order to avoid
damage or injury. If the power cord is replaced by
an equally qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
Labels on Tool
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per
minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
Always remove the plug from the socket before inspecting
a damaged cable. Be careful not to use your strimmer if the
cable is damaged.
Beware of flying objects.
Keep bystanders away from the cutting area.
Do not expose the appliance to rain or high humidity.
Directive 2000/14/EC guaranteed sound power.
SAFETY INSTRUCTIONS

WARNING: When using mains-powered machines,
basic safety precautions, including the following,
should always be followed to reduce the risk of fire,
electric shock, personal injury and material damage.

Using Your Machine

Always take care when using the machine.
• Never allow children or people unfamiliar with these
instructions to use the machine.
• Never operate the machine while people, especially
children, or pets are nearby.
ENGLISH
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
31