Using Your Cooktop; Surface Controls - JENN-AIR JGD8130 Guia Del Usuario

Ocultar thumbs Ver también para JGD8130:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

U
Y
SING
OUR
S
C
URFACE
ONTROLS
CAUTIONS:
• If flame should go out during a
cooking operation, turn the burner
off. If a strong gas odor is detected,
open a window and wait five minutes
before relighting the burner.
• Be sure all surface controls are set to
the OFF position prior to supplying
gas to the cooktop.
• NEVER touch cooktop until it has
cooled. Expect some parts of the
cooktop, especially around the
burners, to become warm or hot
during cooking. Use potholders to
protect hands.
P
I
ILOTLESS
GNITION
Pilotless ignition eliminates the need for a
constant standing pilot light. Each surface
burner has a spark ignitor. When cleaning
around the surface burner use care. If
cleaning cloth should catch the ignitor, it
could damage it preventing ignition.
If the surface burner does not light, check
if ignitor is broken, soiled or wet. If clogged,
clean the small port beneath the ignitor
using straight pin.
PORTS
PORT BELOW IGNITOR
S
C
URFACE
ONTROL
K
NOBS
Use to turn on the
surface burners. An
infinite choice of heat
settings is available
from Lo to Hi. At the
Hi setting a detent or
notch may be felt. The knobs can be set on
or between any of the settings.
C
OOKTOP
S
ETTING THE
C
ONTROLS
1. Place a pan on the burner grate. (To
preserve the grate finish, do not operate
the burners without a pan on the grate
to absorb the heat from the burner
flame.)
2. Push in knob and turn immediately
counterclockwise to the Lite setting
until burner ignites.
• A clicking (spark) sound will be heard
and the burner will light. All ignitors
on the JDG8130 will spark when any
surface burner knob is turned to the
Lite position. On the JGD8345, the
grill burner and center bay burners
will spark when the grill or any center
bay burner is lit. Both of the right hand
bay burners will spark when either
one is lit.
S
UGGESTED
The size and type of cookware will affect the heat setting.
Settings
Hi
CAP
IGNITOR
Lo
3. After ignition, turn knob clockwise to
O
P
1. Hold a lighted match to the desired
2. Push in and turn the control knob
3. Adjust the flame to the desired level.
CAUTION:
H
S
EAT
ETTINGS
Use Hi to bring liquid to a boil, or reach pressure in a
pressure cooker. Always reduce setting to a lower heat when
liquids begin to boil or foods begin to cook.
An intermediate flame size is used to continue cooking. Food
will not cook any faster when a higher flame setting is used
than needed to maintain a gentle boil. Water boils at the same
temperature whether boiling gently or vigorously.
Use Lo to simmer foods, keep foods warm and melt
chocolate or butter.
Some cooking may take place on the Lo setting if the pan is
covered. It is possible to reduce the heat by rotating the knob
toward OFF. Be sure flame is stable.
4
desired setting.
• The ignitor will continue to spark
until the knob is turned past the
Lite position.
D
PERATING
URING A
F
OWER
AILURE
surface burner head.
slowly to Lite.
When lighting the surface burners,
be sure all of the controls are in the
OFF position. Strike the match first
and hold it in position before turning
the knob to Lite.
Uses

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Jgd8345

Tabla de contenido