LOVATO ELECTRIC DMG700 Manual De Instrucciones página 13

M10 - COUNTERS
P10.n.01 Count source
P10.n.02 Channel number (x)
P10.n.03 Multiplier
P10.n.04 Divider
P10.n.05 Counter description
P10.n.06 Unit of measure
P10.n.07 Reset source
P10.n.08 Channel number (x)
Note: This menu is divided into 4 sections, for counters CNT1..4
P010.n.01 = Signal that causes the increment of the counter (on rising edge). It can be the power-on of the multimeter (ON), the overcoming of a limit threshold (LIMx), the activation of an external input (INPx), one
logic combination (BOOx).
P010.n.02 = Number of the channel (x) referred to previous parameter.
P010.n.03 = Multiplying factor. The pulse count is multiplied by this coefficient before being displayed.
P010.n.04 = Dividing factor. The pulse count is divided by this coefficient before being displayed. If different from 1, then the value is displayed with 2 decimals.
P10.n.05 = Description of the counter. Free text 16 characters.
P10.n.06 = Unit of measure of the counter. Free text 6 characters.
P10.n.07 = Signal that causes the clearing of the counter. As long as this signal is activated, the counter remains at value 0.
P10.n.08 = Number of the channel (x) referred to previous parameter.
M11 - PULSES
P11.n.01 Measurement source
P11.n.02 Count unit
P11.n.03 Pulse duration
Note: This menu is divided into 5 sections, for energy count pulses PUL1..5
P11.n.01 = Type of energy to which the pulse is linked to.
P11.n.02 = Quantity of energy for each pulse. (e.g. 10Wh, 100Wh, 1kWh, etc.).
P11.n.03 = Pulse duration.
M12 - BOOLEAN LOGIC
P12.n.01 Operand 1
P12.n.02 Channel number (x)
P12.n.03 Logic operator 1
P12.n.04 Operand 2
P12.n.05 Channel number (x)
P12.n.06 Logic operator 2
P12.n.07 Operand 3
P12.n.08 Channel number (x)
P12.n.09 Logic operator 3
P12.n.10 Operand 4
P12.n.11 Channel number (x)
Note: This menu is divided into 8 sections, for Boolean variables BOO1..8
P12.n.01 = First operand of the Boolean logic.
P12.n.02 = Number of the channel (x) referred to previous parameter.
P12.n.03 = Logic operation between first and second operands.
P12.n.04 = Second operand.
From P12.n.05 to P12.n.11 – (as given above).
M13 - INPUTS
P13.n.01 Input function
P13.n.02 Normal status
P13.n.03 ON delay
P13.n.04 OFF delay
Note: This menu is divided into 8 sections, for digital inputs INP1..8
P13.n.01 = Input function:
OFF – Input disabled
ON – Input enabled, used as a source for counters, Boolean logic, etc.
LOCK – Settings lock. Does not allow access to both levels.
SYNC – Synchronisation for power/energy integration.
TAR-A, TAR-B – Energy tariff selection. See Energy tariffs chapter.
C01...C08 – When this input is activated (edge-triggered), the corresponding command of the commands menu is executed.
P13.n.02 = Normal status of the input. Allows to invert the INPn activation logic.
P13.n.03 – P13.n.04 = Delay on activation – deactivation of the input. Allow to filter the input status to avoid bouncing.
Default Range
OFF OFF-ON-INPx-LIMx-BOOx
1 1-8
1 1-1000
1 1-1000
CNTn (Text - 16 chars)
Umn (Text - 6 chars)
OFF OFF-ON-INPx-LIMx-BOOx
1 1-8
Default Range
kWh+ kWh+,kWh-,kvarh+,kvarh-,kVAh
100 10/100/1k/10k
0.1 0.01-1.00
Default Range
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - AND - OR - EXOR - AND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - AND - OR - EXOR - AND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
- - - - - - - AND - OR - EXOR - AND NOT -
OR NOT - EXOR NOT
OFF OFF-LIMx-INPx-OUTx-REMx-BOOx
1 1 - 8
UdM Default
OFF OFF - ON - LOCK -
SYNC - TAR-A -
C01...C08
OFF
sec 0.05 0.00 - 600.00
sec 0.05 0.00 - 600.00
G
B
Range
TAR-B
OFF-ON
13