Commands Menu - LOVATO ELECTRIC DMG700 Manual De Instrucciones

M14 - OUTPUTS
P14.n.01 Output function
P14.n.02 Channel number (x)
P14.n.03 Idle status
Note: This menu is divided into 8 sections, for digital outputs OUT1..8
P14.n.01 = Function of the output:
OFF – Output disabled
ON – Output always enabled
SEQ – Output enabled in case of wrong phase sequence
LIMx – BOOx – ALAx – PULx – REMx – Output linked to the status of the programmed variable. Allows to connect the status of an output to the status of a limit threshold, a Boolean variable, an alarm, etc.
P14.n.02 = Number of the channel (x) referred to previous parameter.
P14.n.03 = Normal status of the output. Allows to reverse the logic of the output function.
M15 - USER-DEFINED PAGES
P15.n.01 Page enabling
P15.n.02 Title
P15.n.03 Measurement 1
P15.n.04 Measurement 2
P15.n.05 Measurement 3
P15.n.06 Measurement 4
Note: This menu is divided into 4 sections, for user pages PAG1..4
P15.n.01 = Enables user page PAGn.
P15.n.02 = Title of the user page. Free text, 16 chars.
P15.n.03, P15.n.04, P15.n.05, P15.n.06 = Measurement that will be shown in the four frames of the user page.

COMMANDS MENU

– The commands menu allows executing some occasional operations like reading peaks resetting, counters clearing, alarm reset, etc.
– If the Advanced level password has been entered, then the commands menu allows executing the automatic operations useful for the device configuration.
– The following table lists the functions available in the commands menu, divided by the access level required.
Code COMMAND
C.01 RESET HI-LO
C.02 MAX DEMAND RESET
C.03 PARTIAL ENERGY METER RESET
C.04 PARTIAL HOUR COUNTERS RESET
C.05 RESET COUNTERS
C.06 RESET TARIFFS
C.07 RESET ALARMS
C.08 RESET LIMITS
C.11 TOTAL ENERGY METER RESET
C.12 TOTAL HOUR COUNTERS RESET
C.13 PARAMETERS TO DEFAULT
C.14 PARAMETERS BACKUP
C.15 PARAMETERS RESTORE
C.16 WIRING TEST
– Once the required command has been selected, press
– To cancel the command execution press MENU.
– To quit commands menu press MENU.
14
ACCESS LEVEL
User Advanced
G
G
G
G
G
G
G
G
to execute it. The device will prompt for a confirmation. Pressing
Default Range
OFF OFF - ON
PAGn (Text - 16 char)
OFF OFF- (measurements)
OFF OFF- (measurements)
OFF OFF- (measurements)
OFF OFF- (measurements)
DESCRIPTION
G
Clears of HI and LO peaks of all readings
G
Clears of Max Demand of all readings
G
Clears partial Energy meters
G
Clears partial hour counters
G
Clears counters
G
Clears tariff Energy meters
G
Clears alarms with latch
G
Clears limit thresholds with latch
G
Clears total, partial and tariff energy meters
G
Clears total hour counters
G
All set-up parameters are reset to factory default value
G
Saves a backup copy of all set-up parameters
G
Restores the set-up parameters to backup values
G
Carries out the wiring test in order to check proper wiring
of the DMG. See wiring test chapter.
again, the command will be executed.
UdM Default Range
OFF OFF-ON-SEQ-LIMx-
BOOx-ALAx-PULx-
REMx
1
OFF OFF-ON
1 - 8
G
B