Hoover XARION Manual De Instrucciones página 5

To access the exhaust filter:
1. Unlock the exhaust filter door by rotate the door along arrow indicated.
2. Remove the filter pack from recess.
3. gently tap and wash the blue Hepa filter unit. do not use hot water or detergents. Remove
excess water from the filter and leave to dry fully before re-using. [21]
4. Reassemble filter pack once fully dry and refit to the cleaner. Close the door along arrow
indication.
IMPORTANT: do not use the product without the filter pack fitted.
NOTE: ensure the carry handle is at its down position before opening the filter door.
Cleaning the Airvolution separation unit
This cleaner uses the Airvolution separation system, unique to Hoover. If necessary the
Airvolution separation unit can be removed from the dust container and cleaned.
1. Remove dust container from the cleaner by releasing the container carry handle to detach
the dust container from the main cleaner and pull upward to remove. [15]
2. Place the bin on a flat surface and unclip the clips from either side of the dust container.
[22]
3. Using the bin handle lift the bin upper section containing the separation unit from the
lower section. [23]
4. Use a cloth to remove excessive dust from the separation unit's surface.
5. Reassemble the bin upper section. Push clips back to fully close the bin.
6. Refit the dustbin to the cleaner. To lock in place push the container carry handle down
until the latch connects with the main body of the cleaner. Once correctly retained the
carry handle will sits flush with the top of the cleaner.
Removing a blockage
1. Check if the dust container is full. If so refer to 'emptying the dust container.
2. If the dust container is empty but suction is still low:
A. do the filters need cleaning? If so refer to 'Cleaning the washable filters' .
B. Check if there is any other blockage in the system - Use a rod or pole to remove any
blockage from the extension tube or flexible hose.
C. Check if pre-motor filter is fitted and filter door is closed.
d. Check if the separation unit needs to be cleaned. Refer to 'Cleaning the separation
unit' .
Xarion_Green__1-4_union.indd 3
[19]
[20]
[24]
[25]
USeR CHeCKLIST
Should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the dust container over-filled? Please refer to 'Cleaner Maintenance' .
• Is the filter blocked? Please refer to 'Cleaner Maintenance' .
• Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system' . Has the
cleaner overheated? If so, it will take approximately 30 minutes to automatically reset.
IMPORTANT INfORMATION
Hoover spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
• Hepa Pre-Motor filter: S104 - 35600990
• Hepa exhaust filter: T101 - 35600991
• Professional fibre Hose: d112 - 35600984
• Carpet & floor Nozzle: g114 - 35600995
• Parquet Caresse Nozzle: g111 - 35600986
• Miniturbo Nozzle Allergen Remover with Silver Ion Technology: J42 - 35600987
Hoover Service
Should you require service at any time, please contact your local Hoover Service Office.
Quality, Safety and the Environment
Safety
Although safety certification of electrical appliances is not required by law in the UK, Hoover
believe that independent approval is the best way of demonstrating safety in design and
manufacture. The British electrotechnical Approvals Board (BeAB), the independent UK
national authority for the safety of domestic electrical appliances, ensures that european
safety standards are met and maintained throughout the production life of an appliance. All
appliances that pass the requirements are permitted to carry the BeAB mark of safety.
3
GB
03/09/2009 14.22.54