Denon DJ PRINE 4 Guia De Inicio Rapido página 7

55 56 57 57 57 58
60
55 56 57 57
52
48 50
51
47 49
47. FX On: Press these button to enable or disable FX 1 and FX 2.
48. FX Select: Turn these knobs to select the active effect for FX 1 and FX 2.
49. FX Parameter: When lit, press this button to activate the secondary parameter for an effect.
50. FX Parameter Knob: Use these knobs to adjust the effect parameter.
51. FX Reset: Press these buttons to reset the FX Frequency to center.
Press and hold Shift and press these buttons to set the effect to its default state, with Wet/Dry set to 0.
52. FX Frequency: Turn this knob to select a frequency band of the audio singal to which the BPM effects will be
applied. Select the center (12 o'clock) position to apply effects to the entire spectrum of frequencies.
53. FX Wet/Dry Knob: Turn this knob to adjust the wet/dry mix of the effects.
54. FX Beats Buttons: Press either of these buttons to decrease or increase the rate of time-based effects on that
deck.
55. Mic On/Off: Press this button to activate/deactivate the microphones.
56. Mic Level: Turn these knobs to adjust the volume levels of the corresponding microphone inputs. The Peak light
next to each knob indicates the current signal level by its color: green (low), amber (normal/optimal), or red
(maximum/peak). You can adjust the microphone attenuation in the Utility menu.
Important: The audio signals from the microphones are routed directly to the Master Outputs.
57. Mic EQ: Turn these knobs to boost or cut the high, mid-range (Mic 1 only) and low frequencies for the
corresponding microphones.
58. Echo On/Off: Press this button to activate/deactivate the reverb effect on the microphones' audio signal.
59. Mic Echo Level: Turn this knob to adjust the amount of the reverb effect on the microphones' audio signal.
60. Talkover: Press this button to use the "talkover" feature, which automatically reduces the volume level of the
master mix when you speak into the microphone. You can adjust the talkover level in the Utility menu.
61. Master Level: Turn this knob to adjust the volume level of the Master Outputs.
62. Zone Channel Assign: Press this button to set Deck 4 as a Zone Playlist, which will play from the Zone
Outputs. By default, the master output will play through the zone if a zone playlist is not assigned.
63. Zone Level: Turn this knob to adjust the volume level of the Zone Outputs.
64. Zone EQ: Turn these knobs to boost or cut the high and low frequencies for the Zone Outputs.
65. Booth Level: Turn this knob to adjust the volume level of the Booth Outputs.
66. Booth EQ: Turn these knobs to boost or cut the high and low frequencies for the Booth Outputs.
67. SD Card Slot: Insert a standard SD or SDHC card to this slot. When you select that SD card as a source, you
can use the display to select and load tracks on your SD card.
68. USB 1/2 Ports: Connect standard USB flash drives to these USB ports. When you select that USB flash drive as
a source, you can use the display to select and load tracks on your USB flash drive.
Important: You must use the Engine software to configure the music library on your SD Card or USB flash drive
before connecting them to Prime 4. See the complete User Guide at
69. Eject: Press this button to bring up on the touchscreen a list of connected media devices which can be ejected.
Tap one of the listed media sources to eject that device. To prevent data corruption, drives must be ejected
before being removed from the player.
59 58
53
54
62 63 64
61
65 66 66
48 50
49
47
denondj.com to learn how to do this.
64 67 68
69
52 53
51 54
7