B&W CM7 Manual De Instrucciones página 6

each pair of terminals connected to the amplifier
independently. Bi-wiring can improve the resolution of
low-level detail. Figures 2a and 2b illustrate
conventional and bi-wire connection.
Ensure that the positive terminals on the speaker
(marked + and coloured red) are connected to the
positive output terminal on the amplifier and the
negative terminals on the speaker (marked – and
coloured black) are connected to the negative output
terminal on the amplifier. Incorrect connection can
result in poor imaging and loss of bass.
Ask your dealer for advice when selecting speaker
cable. Keep its total impedance below the maximum
recommended in the speaker specification and use a
low inductance cable to avoid attenuation of high
frequencies.
Fine Tuning
Before fine tuning, make sure that all the connections
in the installation are correct and secure.
Moving the speakers further from the walls will
generally reduce the volume of bass. Space behind
the speakers will also help to create an aural
impression of depth. Conversely, moving the speakers
closer to the walls will increase the volume of bass. If
you want to reduce the volume of bass without
moving the speakers further from the wall, fit the foam
plugs or, for less severe bass reduction, the foam rings
in the port tubes. Fitting a foam plug or ring in a port
tube is illustrated in Figure 3.
If the bass seems uneven with frequency this will most
probably be due to resonance modes in the listening
room. Even small changes in the position of the
speakers or the listening position can have a profound
effect on how these resonances affect the sound. Try
moving the listening position or locating the speakers
along a different wall. The presence and position of
large pieces of furniture can also influence resonance
modes.
If the central image lacks focus, try moving the
speakers closer together or angling them inward so
that they point at a location just in front of the listening
position. Figure 1b illustrates speakers angled inwards.
If the sound is too bright, increasing the amount of
soft furnishing in the room (heavier curtains for
example) may help balance the sound. Conversely,
reducing the amount of soft furnishing may help
brighten a dull sound.
Some rooms suffer from "flutter echoes" – echoes that
"bounce" between parallel room boundaries. Flutter
echoes can colour the sound of the speakers in the
room. Test for flutter echoes by standing in the middle
of the room and clapping your hands. Flutter echoes
can be reduced by placing irregular shaped items or
non-reflective surfaces, bookshelves, rugs or pictures
for example, on one of the offending walls or floor.
Ensure that the speaker stands firmly on the floor. Use
carpet piercing spikes if appropriate and adjust them
to take up any unevenness.
Running-in Period
The performance of the speaker will change subtly
during the initial listening period. If the speaker has
been stored in a cold environment, the damping
compounds and suspension materials of the drive
units will take some time to recover their correct
mechanical properties. The drive unit suspensions will
also loosen up during the first hours of use. The time
taken for the speaker to achieve its intended
performance will vary depending on previous storage
conditions and how it is used. As a guide, allow up to
a week for the temperature effects to stabilise and
15 hours of average use for the mechanical parts to
attain their intended design characteristics.
However, longer run-in periods (as long as a month)
have been reported and there is evidence to suggest
that this has little to do with the speaker changing and
more to do with the listener getting used to the new
sound. This is especially so with highly revealing
speakers such as these, where there may be a
significant increase in the amount of detail compared
with what the listener has previously been used to; the
sound may at first appear too "up front" and perhaps
a little hard. After an extended period of time, the
sound will seem to mellow, but without losing clarity
and detail.
Aftercare
The cabinet surfaces usually only require dusting. If
you wish to use an aerosol or other cleaner, remove
the grille first by gently pulling it away from the
cabinet. Spray aerosols onto the cleaning cloth, not
directly onto the product. Test a small area first, as
some cleaning products may damage some of the
surfaces. Avoid products that are abrasive, or contain
acid, alkali or anti-bacterial agents. Do not use
cleaning agents on the drive units. The grille fabric
may be cleaned with a normal clothes brush whilst the
grille is detached from the cabinet. Avoid touching the
drive units, especially the tweeter, as damage may
result.
In order to avoid the risk of the surface finish cracking,
keep the product away from sources of direct heat
such as radiators and warm air vents. Whenever
Bowers & Wilkins speakers are finished in real wood,
the finest veneers are selected and treated with an
ultra-violet resistant lacquer to minimise changes in
colour over time. Nevertheless, like all natural
materials, the veneer will respond to its environment
and a degree of colour change is to be expected. The
effect may be particularly noticeable where the area
covered by the grille, or areas kept in shadow, change
more slowly than other areas. Colour differences may
be rectified by exposing all the veneer surfaces equally
and evenly to sunlight until the colour is uniform. This
process can take several days or even weeks, but
may be accelerated by careful use of an ultra-violet
lamp.
3