stayer VVAC2075 Manual De Instrucciones página 15

Some examples of these chemicals are:
Lead from lead-based paints, crystalline silica from bricks
and cement and other masonry products, and arsenic
and chromium from chemically-treated lumber. The risk
from these exposures varies, depending on how often
you do this type of work.
To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety
equipment, such as dust masks that are specially
designed to filter out microscopic particles.
INTENDED USE
This vacuum cleaner is primarily designed to operate
in conjunction with power tools which require dust
extraction, such as sanders, saws, wall chasers,
scouring machines,
nondangerous dusts, dirt, shavings etc.
This machine may also be used to vacuum water and
other non-flammable and non corrosive liquids.
The end user/operator is solely responsible for any
damage or accident should the machine be used for any
use other than its intended purpose.
PREPARATION AND INITIAL OPERATION
Electrical connection.
The operating voltage shown on the rating plate must
correspond to the voltage of the power supply. Make
sure that the vacuum cleaner is switched off when you
plug the power supply.
This machine must ALWAYS be plugged
into a properly grounded outlet. NEVER
operate the m a c hine if it is not grounded.
This will result in a static electrical build-up
which will destroy the machine's electronic
components.
ASSEMBLY
Follow the sequences in Figures 2 and 3.
OPERATION
Follow the sequence shown in figure 4. You can use the
suction brush held by your hands (fig 4.1) or attached by
the machine (fig 4.3).
SWITCH MODES: ON/OFF
This machine has a multi-mode On/Off Switch.
In position "OFF" the vacuum cleaner is switched off
but there is always current to the Integrated Switching
Appliance Socket.
Different modes of operation are possible:
1.- SWITCH POSITION "MANUAL": The cleaner motor
starts immediately and runs continuously.
etc. This machine
ENGLISH
15
2.- SWITCH POSITION "AUTO –AC": The Integrated
Switching Appliance Socket is live. The cleaner motor
starts only when the tool connected to the appliance
socket is switched on.
There is a 1 second delay in the vacuum starting (to
avoid tripping the circuit breaker) and a 10 second delay
in shutting off (to clear the hose of dust) followed by a
cycle of the filter shaker.
Before turning the switch to the "AUTO –AC" position,
ensure that the tool connected to the appliance socket is
switched off.
Observe the maximum connected load of 2200W for the
Integrated Switching Appliance Socket.
Automatic Filter Shaker Function.
extracts
This machine
electromagnetic
automatically with a cycle every 20 seconds to shake
accumulated dust from the Diaphragm Filter. It will also
cycle when the switch is switched off (both in manual and
automatic modes) It is fully automatic and only operates
when the Diaphragm Filter is in place. When it engages,
there will be a slight noise. This noise is normal and
does not indicate any malfunction of the machine. To
minimize noise, always install the Diaphragm Filter with
the exposed metal side of the anvil facing downwards.
EMPTYING THE DEPOSIT
Follow the sequence in figure 5.
If liquid was sucked use pipe 10 (fig 5.2) to empty by
gravity.
MAINTENANCE
Follow the sequence in figure 6.
You can use water (fig.6.3) to clean the filter.
Vacuum dry media
Not suitable to vacuum hazardous or toxic
substances such as asbestos. The filters m
ay not be able to capture all particles
and may exhaust them back into the
environment.
Before using the vacuum cleaner to extract dry
materials, the machine must set up in a dry vacuuming
configuration.
The pair of Main Pleated Filters must always be in place.
The Filter bag and Diaphragm Filters must both be
mounted at all times.
Note: It is not recommended to dry vacuum when there
is liquid in the tank or if the tank and f i l t ers are still wet.
Severe caking of dust and possible damage will occur.
15
is equipped with an
filter shaker device.
automatic
It operates