Generalinformation; Unpacking; Accessory Box; Assembly - Generac GP Serie Manual Del Proprietário

Ocultar thumbs Ver también para GP Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1.1 UNPACKING
• Removeall packagingmaterial.
• Removeseparateaccessory box.
• Removethe generatorfrom carton.
1.1.1 ACCESSORY
BOX
Checkall contents. If any parts are missing or damaged,locate an
authorizeddealerat 1-888-GENERAC.
• 1 - Owner's Manual
• 1 - HandleAssembly
• 1-LiterOiISAE30
• 1-FrameFoot
• 2 - Never-Flat W heels
• 1 - Battery Charger(electric
start only)
• 1 - HardwareBag (containingthe following):
• 2-Rubber F eet
• 2-M8Bolt(Long)
• 2-1/2" AxlePins
• 2-M8Bolts(Short)
• 2-CotterPins
• 2-M8AcornNut
• 2-1/2" FlatWashers
• 4-HexFlanged M8Nuts
1.2 ASSEMBLY
The generator requires some assembly prior to using it. If
problems arise when assembling the generator, please call the
GeneratorHetplineat 1-888-GENERAC.
1.2.1 ASSEMBLING THEACCESSORY K IT
The wheels are designed into the unit to greatly improve the
portability of the generator.
You will needthe following tools to properly install the accessory
kit.
• NeedleNose Pliers
• Ratchetand a 13mm (1/2") socket
• 13mm (1/2") box wrench
NOTE:
The wheels are net intendedfor over-the-road use.
1.
Refer to Figure 1 and install the Wheels as follows:
• Slidethe Axle Pinsthrough the Wheel, 1/2" FlatWasher,and Wheel
Bracket on the frame.
• Insert the Cotter Pinthrough the Axle Pinthen bend the tabs (ofthe
OotterPins) outward to lock into place.
2.
Refer to Figure 1 and install the Frame Foot and Rubber
Bumpers as shown.
• Slidethe RubberBumper studs through the Frame Footthen install
the Locking FlangeNuts.
• Slide the HexHead Bolts through the holes in the FrameRail.
• Slide the Frame Foot onto the Hex Head Bolts then install the
Locking FlangeNuts.
3.
Refer to Figure 1 and install the Handle as shown.
• Slide the long Bolts through the HandleBracket and Handle,then
install the HexNuts.
Figure 1 - Wheel & Handle Assembly
Y_ H8 ]3r]LT
(LONG)
M8 ACORN NUT--,..,.
-- --
--
L
\_
_
/_2x
M8 BOLT
HANBLE
_
_%,
II
II/
(SHORT)
.
FRAHE
/
7"
\
\
WASHER
FOOTJ
/
_
_2X
COTTER
8X RUBBER FOOTJ
_xPI:8
NUT
1.2.2 STARTER CONNECTION (ELECTRIC STARTONLY)
The unit has been deliberately shipped with the starter cable
disconnected.
To connect starter:
1. Locate starter cable.
2. Pull vinyl boot back onto starter cable.
3. Removenut and washer from starter post.
4. Put starter cable onto post and re-install washer and nut.
2.1 KNOWTHE G ENERATOR
Read the Owner'sManual and Safety Rules before operating
this generator.
Compare the generator to Figures 2 through 4 to become
familiarizedwith the locations of various controls and adjustments.
Savethis manualfor future reference.
1. 120 VoltAC,20 Amp, DuplexReceptacle- Supplieselectrical
powerfor the operationof 120 Volt AC, 20 Amp, single-phase,
60 Hz electrical lighting, appliance,tool and motor loads.
2. 120/240 Volt AC, 30 Amp LockingReceptacle - Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers(AC) - Each receptacle is provided with a
push-to-reset circuit breakerto protect the generatoragainst
electrical overload.
4. Oil Drain - Useto drain engine oil.
5. Air Filter - Filters intakeair as it is drawn into the engine.
6. ChokeKnob - Usedwhen starting a cold engine.
7. Fuel Tank- See generatorSpecificationsfor tank capacity.
8. Grounding Lug - Ground the generatorto an approvedearth
ground here. See "Groundingthe Generator"for details.
g. Run/Step Switch - Controls the operation of the generator
(pull start models only).
gA. Start Switch - Used to start engine from the starter motor
(electricstart models only).
10. Muffler - Quietsthe engine.

Publicidad

Tabla de contenido
loading

Tabla de contenido