Analog Stereo; Other Settings; Temporary Speaker Level; Cop - Rotel RSP-1068 Manual De Instrucciones

Procesador de sonido envolvente
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

RSP-1068 Surround Sound Processor
• To select Dolby multichannel modes
for 2-channel digital recordings. You
can also step through the Dolby options
(Pro Logic II, Pro Logic IIx, or 3-Stereo) by
repeatedly pressing the DOLBY PLIIx/3ST
button on the front panel. You can select
Pro Logic or Pro Logic IIx Cinema or Music
modes by pressing the PLC or PLM buttons
on the remote.
To change the Cinema or Music option in
Pro Logic II mode, press the SUR+ button
the remote twice while in Pro Logic II or Pro
Logic IIx modes. Then, press the +/– buttons
to select the option.
• To select DTS Neo:6 mode for 2-
channel digital recordings. You can
also step through the DTS options (Neo:6
Cinema or Neo:6 Music) by repeatedly
pressing the DTS Neo:6 button on the front
panel.
To change the Cinema or Music option in
Neo:6 mode, press the SUR+ button the
remote twice while in Neo:6 mode. Then,
press the +/– buttons to select the option.
• To select DSP multichannel modes
for 2-channel digital recordings.
You can also step through the DSP options
(MUSIC 1-4, 5CH, 7CH) by repeatedly
pressing the DSP button on the front panel.
Directly select 5CH mode by pressing the
5CH button on the remote. Directly select
7CH mode by pressing the 7CH button on
the remote.

Analog Stereo

890
This type of recording includes any conventional
stereo signal from the RSP-1068's analog in-
puts, including analog audio from CD players,
FM tuners, VCRs, tape decks, etc.
Analog stereo inputs require a choice about
how the signal is routed through the RSP-1068.
One option is the analog bypass mode. In
this mode, the stereo signal is routed directly
to the volume control and the outputs. It is
pure 2-channel stereo, bypassing all of the
digital circuitry. None of the bass manage-
ment features, speaker level settings, contour
settings, or delay settings are active. There is
no subwoofer output. A full-range signal is
sent directly to two speakers.
The other option converts the analog inputs to
digital signals, passing them through the digital
processors in the RSP-1068. This option allows
all of the features to be active including bass
management settings, crossovers, subwoofer
outputs, contour settings, etc. In this mode, you
can select several surround modes including
2-CH Stereo, Dolby 3-Stereo, 5-CH Stereo,
7-CH Stereo modes. You can also use Dolby
Pro Logic II or Pro Logic IIx surround, DTS
Neo:6 surround, or one of the MUSIC 1-4
DSP modes.
NOTE: In addition to the options that fol-
low, you can select Pro Logic II Cinema,
Pro Logic II Music, Pro Logic IIx Cinema,
Pro Logic IIx Music, 5-channel stereo, or
7-channel stereo by pressing one of the
surround mode buttons on the remote (PLC,
PLM, 5CH, 7CH).
• To select Stereo or Analog bypass
mode for 2-channel analog record-
ings. Press the 2CH button on the remote
to toggle between Stereo (with digital
processing) or Analog Bypass (no digital
processing) modes.
• To select any mode for 2-channel
analog recordings. Press the SUR+ but-
ton on the remote, then use the +/– buttons
to step through the optonal modes until the
desired mode is displayed.
• To select Dolby multichannel modes
for 2-channel analog recordings.
You can also step through the Dolby options
(Pro Logic II, Pro Logic IIx, or 3-Stereo) by

COP

repeatedly pressing the DOLBY PLIIx/3ST
button on the front panel. You can select
Pro Logic or Pro Logic IIx Cinema or Music
modes by pressing the PLC or PLM buttons
on the remote.
To change the Cinema or Music option in
Pro Logic II mode, press the SUR+ button
the remote twice while in Pro Logic II or Pro
Logic IIx modes. Then, press the +/– buttons
to select the option.
• To select DTS Neo:6 modes for 2-
channel analog recordings. You can
also step through the DTS options (Neo:6
Cinema or Neo:6 Music) by repeatedly
pressing the DTS Neo:6 button on the front
panel.
To change the Cinema or Music option in
Neo:6 mode, press the SUR+ button the
remote twice while in Neo:6 mode. Then,
press the +/– buttons to select the option.
28
• To select DSP multichannel modes
for 2-channel analog recordings.
You can also step through the DSP options
(MUSIC 1-4, 5CH, 7CH) by repeatedly
pressing the DSP button on the front panel.
Directly select 5CH mode by pressing the
5CH button on the remote. Directly select
7CH mode by pressing the 7CH button on
the remote.

Other Settings

Temporary Speaker Level

The levels of all channels should be calibrated
using the TEST TONE procedure during the
initial setup of the RSP-1068. You can make
a temporary change in the relative volume of
the center, surround, center back, or subwoofer
channels using buttons on the remote control
or the front panel controls. These temporary
adjustments only remain in effect until a dif-
ferent input is selected or until the RSP-1068
is turned off.
To adjust speaker levels using the
remote:
1. Press a selection button on the remote to
select a channel (or pair of channels) for
adjustment. Press the C button to adjust
the CENTER channel. Press the S button to
adjust the SUBWOOFER channel. Press the
R button to adjust the rear SURROUND or
CENTER BACK channels (each press of the
R button toggles between the SURROUND
channels and the CENTER BACK channels).
The selected speaker and its current setting
appear briefly in the display.
2. Use the UP or DOWN buttons on the remote
to adjust the output level of the selected
channel(s).
NOTE: If no level adjustment is made for
10 seconds, the levels revert to the default
calibrated settings.
As you select a speaker in the above adjust-
ments, you may notice an addition choice,
"group delay". See the following for an
explanation of this feature.
BM

Publicidad

Tabla de contenido
loading

Tabla de contenido