T Rouble S Hooting - FlexiForce forceIQ Manual De Instrucciones

5. T rouble s hooting
5.1 E vent m essage
Event m essage
OSE 1 E RROR
OSE 2 E RROR
SAFE.EDGE 1 E RR.
SAFE.EDGE 2 E RR.
4W-­‐PHOTOC. E RROR
DOOR S AFETY
MOTOR S AFETY
BLOCKED P OSITIONER
INVERTER E RROR
BATTERY E MPTY
OUT O F R ANGE
UNAUTHORIS. M OVE
DOOR T OO S LOW
DOOR T OO F AST
WRONG D IRECTION
ERROR B AD C ONFIG
FACTORY R ESET
ENDPOS. C HANGED
SEC.DEV. C HANGED
REVERSED 3 T IMES
MEMORY F AULT R AM
MEM. F AULT F LASH
MEM.FAULT E EPROM
SYSTEM P OWER U P
PASSDOOR O PEN
OSE 1 T RIGGERD
OSE 2 T RIGGERD
SAFE. E DGE 1 T RIGGERD
SAFE. E DGE 2 T RIGGERD
4W-­‐PHOTOC. T RIGGERD
5.2 t rouble s hooting
Problem
Error c ode w on't d isappear f rom d isplay e ven i f s afety
edge a re O K.
" Blocked p ositioner"
"Blocked o ut o f r ange / s tutter m ode"
Operator i s n ot m oving, b ut y ou c an h ear t he c ontact
switch c licking
Not p ossible t o a djust e nd p ositions
display w ithout t ext
Quick r elease w on't w ork
Safety e dge w on't w ork
Can't s hut o f F orce I R
ForceLC2 r eact s pontaneously
Operator w on't g o u p/down o nly b uzzing n oise
Forgot t he p assword
Safety d evice o n O SE 1 p ort i s d efect K L3
Safety d evice o n O SE 2 p ort i s d efect K L4
Safety d evice o n S R1 p ort i s d efect K L2:1-­‐2
Safety d evice o n S R2 p ort i s d efect K L2:3-­‐4
Safety d evice o n 4 wire p ort i s d efect
Safety c hain t riggered, o pen c ircuit K L 7
Safety c hain t riggered, o pen c ircuit K L 8
Encoder c ommunication e rror o r n o e ncoder K L18
Inverter c ommunications e rror
Dalmatic e ncoder r eports i ts b atteries a re e mpty
Door m oved p ast t he e nd p ositions
Door m oved w hen i t w as n ot s upposed t o
Door d id n ot m ove e ven t hough i t s hould h ave
Door w as m oving t oo f ast ( door s peed m onitoring)
Door w as m oving i n t he w rong d irection
The s tored c onfiguration w as m issing/invalid
Factory r eset h as b een i ssued f rom t he m enu
The e nd p ositions h ave b een c hanged i n m enu
Safety d evice s etting h as b een c hanged
The d oor h as r everse X t imes i n a r ow a nd a uto c lose h as b een d isabled a s a r esult
Error h as b een d etected d uring t he R AM s elf t est
The f lash C RC c alculation h as d etected a n e rror
The E EPROM C RC c alculation h as d etected a n e rror
System h as b een r eset a nd i s n ow s tarting u p
Pass d oor h as b een o pened w hile t he d oor w as m oving
Safety d evice c onnected t o K L 3 i s a ctivated
Safety d evice c onnected t o K L4 i s a ctivated
Safety d evice c onnected t o K L2 1 -­‐2 i s a ctivated
Safety d evice c onnected t o K L2 1 -­‐2 i s a ctivated
Safety d evice c onnected t o K L5 i s a ctivated
Clear h istory f ile i n s ervice s ettings
Adjust l imit s witch t ype/ c heck e ncoder c onnection
Use s afety c hain/crank o r h and t o m ove t he d oor i n r ight
position.
-­‐ C heck F uses F 1,F2 a nd F 3
-­‐Check i ncoming P ower ( 230V b etween N e n L )
-­‐ C ould h appen a fter u sing t he q uick r elease.
L ock t he d oor i n p osition b y m oving i t a l ittle b y h and.
-­‐ C heck e ncoder s ettings
Check c onnection c able b etween c over a nd c ontrolbox.
The r ed s tripe o n t he f latcable h as t o b e o n t he l eft s ide.
Make s ure t here i s t ension o n t he c ables a nd t he s prings.
Bottom a djustment c an b e t o t ight o n t he f loor.
If y ou h ave m echanical l imit s witch, m ake s ure y ou h ave
connected K L19 p in 5 a nd 6 . Y ou c an c onnect t hem
together. P lug p ower b ack o n.
Make s ure t hat I f y ou u se a n o ptosensor
both t ransmitters a re o n t he s ame s ide o f t he d oor.
Make s ure t he d oor c overs u p a ll t he l ed's
230V o perator:Check i f w ire W f rom K L10 i s c onnected t o
the b lue w ire i n t he m otor.
400V o perator: c heck t he 3 p hases a nd t he f uses.
Contact y our s upplier.
www.flexiforce.com
manual – forceIQ
Reason
Solution
33
33