Operating The Tool - Campbell Hausfeld CHN104 Instrucciones De Operación

General Safety Information
(Continued)
repair, clearing a jam, or moving
the tool to a new location. Always
reconnect the air line BEFORE loading
any fasteners. Do not load the tool
with fasteners when either the
trigger is depressed or the Work
Contact Element (WCE) is engaged.
The tool could eject a fastener
causing death or serious personal
injury.
•
Always fit tool
with a fitting or
hose coupling on
or near the tool
in such a manner
that all compressed
air in the tool is discharged at the
time the fitting or hose coupling is
disconnected. Do not use a check
valve or any other fitting which
allows air to remain in the tool.
Death or serious personal injury
could occur.
•
Never place hands or any
other body parts in the
fastener discharge area of
the tool. The tool might
eject a fastener and could
result in death or serious personal
injury.
•
Never carry the tool by
the air hose or pull the
hose to move the tool
or a compressor. Keep
hoses away from heat,
oil and sharp edges.
Replace any hose that
is damaged, weak or
worn. Personal injury or tool damage
could occur.
•
Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe
distance from the work area in case
of accidental discharge of fasteners.
Do not point the tool toward
yourself or anyone whether it
contains fasteners or not. Accidental
triggering of the tool could result in
death or serious personal injury.
•
Do not drive a fastener
on top of other
fasteners. The fastener
could glance and cause
death or a serious
puncture wound.
•
Do not operate or
!
allow anyone else
to operate the tool
if any warnings
or warning labels
are not legible.
Warnings or warning labels are
located on the tool magazine and
body.
•
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make
the tool unusable or unsafe. If the
tool has been dropped or thrown,
examine the tool closely for bent,
cracked or broken parts and air leaks.
STOP and repair before using or
serious injury could occur.
Caution indicates
a potentially
hazardous situation which, if not
avoided, MAY result in minor or
moderate injury.
•
Do not make any modifications to
the tool without first obtaining
written approval from Campbell
Hausfeld. Do not use the tool if
any shields or guards are removed
or altered. Do not use the tool as
a hammer. Personal injury or tool
damage may occur.
•
Avoid long extended periods of work
with the tool. Stop using the tool if
you feel pain in hands or arms.
•
Always check that the
Work Contact Element
(WCE) is operating
properly. A fastener
could accidentally be
driven if the WCE is not
working properly. Personal injury
may occur (See "Checking the Work
Contact Element" Section).
•
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the tool. Personal injury may
occur.
3
WARNING
information, that if not followed, may
cause damage to equipment.
•
Avoid using the tool when the
magazine is empty. Accelerated wear
on the tool may occur.
•
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
•
Air compressors providing air to the
tool should follow the requirements
established by the American National
Standards Institute Standard
B19.3-1991; Safety Standard for
Compressors for Process Industries.
Contact your air compressor
manufacturer for information.

operating The Tool

lUbRICaTIoN
This tool requires lubrication before
using the tool for the first time and
before each use . If an inline oiler is
used, manual lubrication through the
air inlet is not required on a daily basis .
damaged by excessive lubrication.
Proper lubrication is the owner's
responsibility. Failure to lubricate
the tool properly will dramatically
shorten the life of the tool and void the
warranty.
1 . Disconnect the
air supply from
the tool to add
lubricant .
2 . Turn the tool so
the air inlet is facing
up . Place 4-5 drops of
30 W non-detergent oil
into air inlet . Do not
use detergent oils, oil
additives, or air tool oils . Air tool oils
contain solvents which will damage
the tool's internal components .
3 . After adding oil, run
tool briefly . Depress
the Work Contact
Element (WCE) against
the work surface . Pull
the trigger . Wipe off any excess oil
from the cap exhaust .
ChN104
Notice indicates
important
The work surface
can become
www.campbellhausfeld.com