Dimplex OPH13 Manual De Instrucciones página 3

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
Because the Dimplex Outdoor Patio Heater contains no moving parts
little maintenance is required. Before undertaking any maintenance
work on the heater due attention must be paid to the following:
This heater is designed to be horizontally wall mounted only, it must
not be ceiling mounted.
Always ensure a safe mounting height, at or above a minimum height
of 1.8 metres from ground level, so that the heater can not be touched
when in operation.
This appliance is not intended for use by children or other persons
without assistance or supervision if their physical, sensory or mental
capabilities prevent them from using it safely. Children should be
supervised to ensure that they do not play with the appliance.
The heater must be wall mounted level ± 5º to the horizontal.
Do not locate the heater immediately above or below a fixed socket
outlet or connection box.
Always disconnect the heater from the electricity supply before
attempting to work on or near it.
Always ensure a safe means of access using an access tower or properly
supported ladder.
Do not cover the heater.
Keep combustible materials away from the heater.
Do not position patio furniture, sunshades, curtains, awnings and
other combustible materials too close to the heater.
Do not look into the heater for prolonged periods.
Do not use the heater if the elements are broken - as injury may occur.
Allow adequate time (minimum of 30 mins.) for the elements and body
casing to cool before attempting to work on the heater.
Do not allow the supply cord to sit or hang in front of the heater while
in use.
If the supply cord is damaged, the heater should not be used, it must
be replaced by an assembly available from the manufacturer or service
agent.
Note: Provide sufficient slack to the cable to allow for angular adjustment
of the body.
Always handle the Halogen bulb without touching the glass (by gripping
the ceramic ends gently but firmly) to maximise bulb life.
General
The OPH range of heaters are especially designed for use on Patio Areas. The
heaters provide warmth and comfort for recreational areas. The OPH13 uses
quartz elements which emit a warm glow of medium wave infra-red. The
OPH20 uses Halogen elements which produce a high proportion of their output
in the short-wave infra-red. This provides a high comfort factor – similar to the
natural energy from the sun.
The IPX4 rating means the appliance is suitably rated to be permanently
installed either internally or externally.
Electrical
The installation of this appliance should be carried out by a competent electrician
and be in accordance with the current IEE wiring regulations and any local or
insurance regulations.
The OPH13 & OPH20 are designed for use on a 230-240V AC single phase
supply. A double pole isolating switch with a minimum separation of 3mm in
each pole must be fitted to facilitate isolation. This switch must either be
positioned inside a building or have an IP rating against water ingress suitable
for external installation. The appliance must be supplied through a residual
current device (RCD) having a rated residual operating current not exceeding
30mA. The RCD for the OPH20 should be type 3 or C rated, with a tripping
coefficient of 7-10 times the rated current. Any other switching device should
be Tungsten lamp rated. The appliance must be connected to a socket-outlet
having an earthing contact.
Installation – Wall Mounting
Heaters are supplied with an integral wall bracket which may be fixed through
the mounting holes to any suitable structure. The bracket allows the heater to
be inclined at the required angle. The recommended fixing height to the centre
line of the bracket is 2.0m from ground level - see Fig. 2. The integral wall
fixing bracket may be removed by fully unscrewing to facilitate its fixing. The
siting of the heater(s) should be such as to allow an even and uninterrupted
distribution of radiation to the area(s) to be heated. Heaters are most effective
when the beam angle is inclined down at an angle of between 30º to 45º to the
vertical - see Fig. 2. When deciding upon the best location, consideration must
be given to the following requirements:
a. Avoid structures which might vibrate e.g. crane gantries. These could
adversely affect element life.
b. Comfort and safety could be compromised unless the heater is mounted at
or above 1.8m from ground level.
c. Allow a minimum of 500mm minimum clearance between the top of the
heater and any horizontal surface- see Fig.1.
Installation – Pole Mounting
The OPH range of patio heaters can be permanently mounted to parasols,
poles or other support structures. A mounting kit (OPHMK1) can be obtained
directly from Dimplex or any of its service agents. Refer to the instructions
supplied with this kit for further advice.
Element Replacement OPH20 (see Fig. 3)
WARNING – BEFORE UNDERTAKING THIS TASK ENSURE THE HEATER IS
DISCONNECTED FROM THE ELECRICITY SUPPLY AND LEFT TO COOL
FOR A MINIMUM OF 30 MINUTES.
1. Remove the four screws which hold the two front panels onto the heater.
2. Slide the guard out on either side.
3. Disconnect the element wires from the terminal blocks.
4. Unclip the lamp from spring clips and pull out the lamp with the wires.
5. Feed the wires of the new lamp back through the insulation.
6. Clip in the new lamp.
Note: Take care not to touch the bulb with bare hands.
7. Reconnect the wires.
8. Replace the guard and top panels.
Element Replacement OPH13 (see Fig. 3)
WARNING – BEFORE UNDERTAKING THIS TASK ENSURE THE HEATER IS
DISCONNECTED FROM THE ELECRICITY SUPPLY AND LEFT TO COOL
FOR A MINIMUM OF 30 MINUTES.
1. Remove the two screws which hold the one of the front panels onto the
heater.
2. Slide out the guard.
3. The lamps are held by spring connectors, push against these to remove the
lamp.
4. Insert the new lamps using the same method.
5. Replace the guard.
6. Replace the front panel.
Cleaning and User Maintenance
WARNING: BEFORE UNDERTAKING CLEANING OR MAINTENANCE WORK
ON THE APPLIANCE, DISCONNECT THE ELECTRICITY SUPPLY.
Since the appliance contains no moving parts little maintenance is required
beyond cleaning and element replacement. It is however essential that the
heater is not operated with an accumulation of dust or dirt on the element, as
this can cause a build up of heat and eventual damage. For this reason the
heater must be inspected regularly, depending upon conditions and at least at
yearly intervals. Allow adequate time for the element and body casing to cool
before attempting to work on the heater - a minimum time of 30 minutes is
recommended.
Clean the lamp(s) and reflector using a mild detergent solution and soft cloth.
Do not use any abrasive or caustic cleaners. Dry with a soft cloth. Avoid
touching either the lamp sleeve or the aluminium reflector with bare fingers. If
they are accidentally touched, remove any fingerprints using a soft cloth
moistened with methylated spirits.
Recycling
For electrical products sold within the European Community. At the
end of the electrical products useful life it should not be disposed of
with household waste. Please recycle where facilities exist. Check
with your Local Authority or retailer for recycling advice in your
country.
After Sales Service
Should you require after sales service or should you need to purchase any
spares, please contact the retailer from whom the appliance was purchased or
contact the service number relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance as this may
result in loss or damage and delay in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
(IPX4) UK