Trademarks; Safety Information; Operating Safety - Mitel Aastra 400 Serie Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 17
Welcome to Aastra

Trademarks

Aastra® is a registered trademark of Aastra Technologies
Limited, A Mitel Company.
All other trademarks, product names and logos are
trademarks or registered trademarks of their respective
proprietors.
Usage of third party software
Aastra 400 products comprise, or are partially based on,
third-party software products. The licence information
for these third-party products is listed in the User's
Guide of the product in question.
Exclusion of Liability
(Not applicable for Australia. See chapter "Limited War-
ranty" for Australia.)
All parts and components of the Aastra 400 communi-
cation solution are manufactured in accordance with
ISO 9001 quality guidelines. The relevant user informa-
tion has been compiled with the utmost care. The func-
tions of the Aastra 400 products have been tested and
approved after comprehensive conformity tests. None-
theless errors cannot be entirely excluded. The manu-
facturers shall not be liable for any direct or indirect
damage that may be caused by incorrect handling,
improper use, or any other faulty behaviour. Potential
areas of particular risk are signalled in the appropriate
sections of the user information. Liability for loss of
profit shall be excluded in any case.
Environment
Aastra 400 products are delivered in recycled, chlorine-
free corrugated cardboard packaging. The parts are
also wrapped inside a protective fleece made of poly-
ethylene foam fleece or polyethylene film for added
protection during shipping. The packaging is to be dis-
posed of in accordance with the guidelines stipulated
under current legislation.
Aastra 400 products contain plastics based
on a pure ABS, sheet steel with an alumin-
ium-zinc or zinc finish, and epoxy resin-
based PCBs. These materials are to be dis-
posed of in accordance with the guidelines
stipulated under current legislation.
Aastra 400 products are disassembled exclusively using
detachable screwed connections.
4

Safety Information

Reference to hazards
Hazard warnings are affixed whenever there is a risk
that improper handling may put people at risk or cause
damage to the Aastra 400 product. Please take note of
these warnings and follow them at all times. Please also
take note in particular of hazard warnings contained in
the user information.

Operating Safety

Aastra 400 communication systems are operated on
230 VAC mains power. Communication servers and all
their components (e.g. terminals) will not operate when
mains power fails. Interruptions in the power supply
will cause the entire system to restart. A UPS system has
to be connected up-circuit to ensure an uninterruptible
power supply. Up to a specific performance limit a
Aastra 470 communication server can also be supplied
redundantly using an auxiliary power supply. For more
information please refer to your communication
server's system manual.
When the communication server is started for the first
time, all the configuration data is reset. You are advised
to backup your configuration data on a regular basis as
well as before and after any changes.
Installation and operating instructions
Before you begin with the installation of the Aastra 400
communication server:
Check that the delivery is complete and undamaged.
Notify your supplier immediately of any defects; do
not install or put into operation any components
that may be defective.
Check that you have all the relevant user documents
at your disposal.
During the installation follow the installation instruc-
tions for your Aastra 400 product and observe to the
letter the safety warnings they contain.
Any servicing, expansion or repair work is to be carried
out only by technical personnel with the appropriate
qualifications.
20350987
syd-0349/1.4 – R3.0 – 05.2014

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Aastra 415Aastra 430Aastra 470

Tabla de contenido