Installation And Setup; Operation - Chemfree SmartWasher SW-05 Manual De Operación

INSTALLATION
AND SETUP
Your SmartWasher is shipped fully assembled. (The OzzyMat,
support grid and false bottom of the sink are packed inside the
sink). Visually inspect for damage (minor scratches and scuffs
are normal due to the molding process).
The SmartWasher will weigh approximately 300 pounds (136 Kg)
when it is filled with fluid. It should be installed close enough to a
nominal 115 VAC (220VAC), Ground Fault Circuit Interrupter (GFCI)
electrical outlet so that it can be plugged in. The SmartWasher should
be the only item plugged in to this circuit. Do not plug in before
adding fluid.
PARTS WASHER SETUP
1. Remove the false bottom and
check to make sure the mat
support grid is in the bottom of
the sink. Remove and discard
packing material
2. Remove the OzzyMat from its
package, unfold it and lay it on
the mat support grid (white side
up).
3. Place the false bottom in
position in the sink.
4. Form the flexible nozzle to its desired shape and be sure
that the parts brush is inside the sink.
5. At start up, carefully add 25 gallons (five 5-gallon boxes) of
OzzyJuice to the SmartWasher by slowly pouring the
solution directly into the sink.
6. Plug the unit in to a 115V (220VAC) GFCI electrical outlet.
7. Push the "Standy/Ready" button FIRST to power up. If
you put "Flow Start/Stop" first you must unplug/replug the
machine to reset the control panel.
8. The SmartWasher will take approximately four hours to heat
up to its optimal temperature of 105° F(+-5°) (40°C)(+-5°).
This temperature will be maintained as long as the
SmartWasher is plugged in and full of OzzyJuice. (If the low
fluid light is on, the heater automatically shuts off.)
PARTS WASHER OPERATION
1. The pump on your SmartWasher can be turned on by
pushing the knee switch (labeled "Push to Start Flow") or
pushing on the Flow Start / Stop button. When you push the
Start / Stop button the fluid will continue running until the
Start / Stop button is pressed again. The knee switch is
connected to a timer which automatically stops the fluid flow
after 10 minutes.
2. Adjust the valve at the base of the faucet to control the flow
of the fluid through the faucet. The valve at the base of the
brush hose controls the flow of fluid through the brush. Both
outlets can be operated independently or together.
The OzzyMat must be changed at least every 30 days or the
OzzyMat – FL-3/FL-4
The OzzyMat traps sludge and dirt as
small as 50 microns. It works effectively
even when it appears dirty. At some
point, however, it will become saturated
and unable to pass fluid freely and
must be changed. The Smart Washer
has bypass openings located under the false bottom of the sink
to accommodate overflow when the OzzyMat is clogged.
False Bottom
White
REPLACING THE OZZYMAT
Side UP
(Must be done every 4 weeks!)
OzzyMat
1. Make sure the pump is
Mat Support Grid
2. Lift out the false bottom
3. Remove the soiled OzzyMat.
4. Remove a new OzzyMat from its poly bag, unfold it and lay
5. Wring excess fluid on to new OzzyMat. It is important to
6. Place used OzzyMat into the poly bag the new mat came in.
CHECK LOCAL REGULATIONS
You may be able to dispose of your used OzzyMat as solid
waste or with your other absorbent mats.
IMPORTANT MAINTENANCE NOTE
Ozzy microbes will lose their effectiveness!
not running.
of the sink and lean to
one side.
it on top of the support grid with the white side up.
WRING used OZZYMAT prior to disposal.
1