BH FITNESS G868i Instrucciones De Montaje página 13

Fig.2 Screws and fasteners.
(82) Bushing.
(64) Screws M-8x15.
(65) Screws M-8x20.
(80) Screws M-8x70.
(59) Screws M-8x60.
(83) Screws M-5x25.
(44) Screws 5x20.
(51) Screws 5x12.
(84) Screws 4x25.
(55) Washers D-8.x16
(66) Washers D8,4x38Ø.
(69) Washers M-8X28Ø.
(58) Spring washer M-8.
(81) Nylon nuts M-8.
(125) Spring washer M-10.
(70) Support plate
Allen key 6mm.
Allen key 6mm.
Double ended ring spanner 13-15.
2. FITTING THE STABILISER BARS.-
ATTENTION: The assistance of a second person is
required for this stage of the assembly.
Bring the front stabiliser bar with wheels (13) to the
main body (1) positioning the wheels at the front of the
unit, Fig.3, Insert the screws (59), fit the washers (55)
and spring washer (58), and tighten securely.
Take the rear stabiliser with adjustable feet (3), and
line up the dots, Fig.4. Insert the screws (59), fit the
washers (55) and spring washer (58), and tighten
securely.
Next, fit the fornt trim cover (92) and tighten using
screws (44) Fig.4.
IMPORTANT: It is advisable to retighten these
screws after one month of using the machine.
3. FITTING THE MAIN POST.-
Next, bring the main post (2) up to boss on the main body
(1), Fig.7, connect the terminals.
Slip the main post (2) over the boss on the main body
(1) in the direction of the arrow, Fig.7, making sure not
to snag any of the cables.
Refit the screws (64), the washers (55) and the spring
washers (58), Fig.7, and tighten securely.
4. FITTING THE FOOT BARS.-
Then fit take the left foot (9) (marked with the letter "L")
and insert the end bush onto the drive spindle (E) on
the main body (1) Fig.5.
Insert screw (65), as shown in Fig.5, then fit the flat
washer (69) and spring washer (58) and (125), and
tighten securely.
Take the right foot bar (10), (marked with the letter "R")
and go through the same assembly procedure as with
the left Fig.5.
Place the left and right axel embellishment cover (111),
fix them with screws (51) as shown in Fig.5.
Next place the foot wheel embellishment covers (108
and 109), screw them on with the screws (51) Fig.5.
5. FOOTREST ASSEMBLY.-
Pick up the left footrest (11) marked with the letter (L),
and insert the axle in the foot strap (9) Fig.5.
Perform the same assemble with the right footrest (12)
marked with the letter (R) in the foot strap (10) Fig.5.
ATTENTION: It is advisable to retighten these
screws after one month of using the machine.
6. FITTING THE FOCUS BARS.-
Insert the left focus bar (7) (marked with the letter "L")
onto the focus bar spindle Fig.8, fit the washered bolts
(69) and spring washer (58) and (125) and the flat
washers (65) and with the help of the box spanners
tighten securely.
Take the right focus bar (8), (marked with the letter "R")
and go through the same assembly procedure as with
the left.
7. FITTING THE FOOT STRAP.-
Fit the foot strap (11) and position it with the lower
focus bar (7) as shown in Fig.8, lining up the holes. Fit
the bushings (82).
Next, insert the bolt (80) and tighten using nut (81). Fit
the foot strap (12) and position it with the lower focus
bar (8) as shown in Fig.8, lining up the holes.
Next, insert the bolt (80) and tighten using nut (81).
Next place the lower rod closure caps (107 and 108),
fix with screws (83 and 51) Fig.8.
If you feel the foot strap has looseness, follow these
steps:
- Remove the bolt.
- Add one or more 0.15 mm washers (125) as
shown in figure 8.
- Tighten again bolt.
8. FITTING THE UPPER FOCUS BARS.-
Once you have assembled the top focus bars, take the
lower focus bar (5) (marked with the letter "L") and insert it
onto the boss for the top bar (7), Fig.9, lining up the holes
for the screws.
Refit the screws (65), the washers (55) and the spring
washers (58), Fig.9, and tighten securely.
Go through the same procedure for the lower right
focus bar (6) (marked with the letter "R").
9. FITTING THE FOCUS BAR SPINDLE
COVERS.-
Take the front (105) and rear (106) covers and
position them on the main post (8), Fig.9. Now use
the screws (51) to attach them to the post.
Take the front (105) and rear (106) covers and
position them on the main post (7), Fig.9. Now use
the screws (51) to attach them to the post.
13
MOD. G868i