Safety Advice - Dreve Drufomat scan Instrucciones De Trabajo

Drufomat scan

4. Safety advice

Attention! Read the following notes before connecting and putting the unit into
service. The operating service and the function of the unit can only be guaranteed for,
if the general safety and accident prevention instructions of the legislation as well as
the safety instructions of the working instructions are observed.
1. This unit must only be used accord-
ing to the present working instructions.
We cannot be held liable for damages
which have been caused by improper
treatment resp. faulty manners of oper-
ation.
2. Put the unit onto a stable and even
basis which is suitable for the operation
weight of approx. 20 kg of the unit.
3. In order to avoid the intrusion of
water into the unit (e. g. splash water)
the unit is to be placed in a dry sur-
rounding.
4. Do not store any flammable sub-
stances in the close surrounding of
the unit.
5. The indicated voltage on the type
plate has to meet the voltage of the
power source.
6. The unit must only be connected
with a socket with protective conductor.
Never touch the plug with wet hands.
7. Authorised operators: The operating
company of the machine has to hold
the working instructions at the oper-
ators' disposal and has to make sure
that authorised operators have read
32
and understood the manual. Only in
that case the operators may operate
the unit.
8. The unit has to be examined before
operation in view of proper condition
and operating safety. If the unit is not
in proper condition, it must not be used
and has to be marked accordingly.
9. The pressure of the compressed air
line must not exceed 145 psi.
10. Do not intrude any objects into
the unit.
11. Do not lock-up the operation ele-
ments of the unit.
12. Do not block the downwards-mov-
ing piston.
13. Do not touch the downwards-mov-
ing piston.
14. The swivelling housing of the radia-
tor reaches high temperatures and must
therefore not be touched – not even for
short moments.
15. If the unit is not used, please dis-
connect the mains.
16. Plates and labels have to be main- the manufacturer. We are not responsi-
tained in a well legible condition and ble for damages caused by the use of
must not be removed. foreign parts.
17. Before cleaning and maintenance 20. Arbitrary rebuilding or modifica-
of the unit or the exchange of parts the tions are not permitted due to safety
plug has to be disconnected. reasons.
18. The opening of the unit and repairs 21. The required operation and main-
are only to be carried out by accordingly tenance conditions mentioned in these
trained experts. working instructions are to be complied
with imperatively.
19. Only those appliances and spare
parts may be used which are released by
5. Initiation
Before initiation make sure that the volt- Important: Before the first initiation
age indicated on the type plate meets please read the working instructions
the voltage of the power source. thoroughly. In case of comprehen-
sion problems contact your responsi-
Connect the unit to an air compressor. ble dealer or Dreve Dentamid GmbH,
Push the pressure hose (included in the if necessary.
delivery) into the compressed air con-
Scope of delivery
nection (9) until it is locked in place. The
hose does not need any further fasten- 1 x Drufomat scan
ing. To release the pressure hose push 1 x drawer for granules
the blue ring upwards and draw the 1 x F insert incl. insert bowl and nub
hose off by pulling downwards.
1 x tension ring with exhaust valve
The pressure of the compressed 1 x base range of blanks
air line must not exceed 145 psi. 1 x bowl for granules
1 x power cord
Put the power cord into the female 1 x air connection hose incl. hose
connector (33) and create a connec-
tion with the Euro/USA plug. 1 x working instruction
plate
clamps and fast coupling
33 33