Nice Era Mat A Instrucciones Y Advertencias De Instalación Y Uso página 14

01
5
sec.
03
x 1 = vento a 5 Km/h
x 1 = wind at 5 Km/h
x 2 = vento a 10 Km/h
x 2 = wind at 10 Km/h
x 3 = wind at 15 Km/h( * )
x 3 = vento a 15 Km/h( * )
0,5
x 4 = wind at 30 Km/h
x 4 = vento a 30 Km/h
sec.
x 5 = wind at 45 Km/h
x 5 = vento a 45 Km/h
Notes:
– When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press any key and
wait 60 seconds for the motor to perform 6 movements.
– If you use a sensor equipped with a "trimmer", you must read the sensor instructions and adjust the threshold directly on the sensor.
6.4 - Adjustment of "Sun" climate sensor
Attention! – After this programmation, the automatic operation of the engine will only happen if it was programmed the close / partial opening "H" (paragraph 5.9), otherwise
the engine will not move.
At the factory, the intervention threshold to is set at level 3 and to change it you must take the following steps.
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
n
01. Keep the key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
t
02. Keep the key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
Briefly press the t key a few times, depending on the level you want to set for the intervention threshold:
03.
1 press = 5 Klux
2 presses = 10 Klux
3 presses = 15 Klux (factory setting)( * )
4 presses = 30 Klux
5 presses = 45 Klux
After about 10 seconds, the motor performs the number of movements indicated by the level number selected. Note - If this does not occur, cancel the procedure. This
way, the adjustment is completed without changing the factory setting.
n key pressed and wait for the motor to perform 3 movements. Upon completion, release the key.
04. Keep the
01
5
sec.
03
x 1 = 5 Klux
x 2 = 10 Klux
x 3 = 15 Klux( * )
0,5
x 4 = 30 Klux
sec.
x 5 = 45 Klux
Notes:
– When performing the procedure, at any time you can cancel it by keeping the n and t keys pressed simultaneously for 4 seconds. Otherwise, do not press any key and
wait 60 seconds for the motor to perform 6 movements.
– If you use a sensor equipped with a "trimmer", you must read the sensor instructions and adjust the threshold directly on the sensor.
6.5 - Pair of photocells
(Wires to use: White + White-black). This accessory makes it possible to detect an obstacle accidentally present along the stroke of the rolling shutter. detection of the
obstacle immediately stops the Lowering manoeuvre of the shutter. For further information, refer to the instruction manual for the photocells.
Attention! – Before connecting the photocells, you must memorize at least the first transmitter (paragraph 5.5) and limit switch "0" and "1" (paragraph 5.6 /
5.7 / 5.8).
6.6 - Resistive sensitive edge
(Wires to use: White-orange + White-black). This accessory, with a constant resistance value of 8.2 K, makes it possible to detect the presence of an accidental obstacle
along the shutter closing trajectory. Considering the heights of the two limit switches and an "R" position that approximately 5 cm from the lower limit switch "1", the system
will behave as follows: a) if the obstacle is detected in the space between the "0" limit switch and the "R" height, the system stops the motor and commands a brief inversion
of motion; b) if the obstacle is detected in the space between the "1" limit switch and the "R" height (a space of approximately 5 cm), the system will behave in the mode
selected by the installer with the following procedure (the available options can be found at point 05 of the procedure). Then, after installing and connecting the sensitive
edge, perform the following procedure.
Before starting the procedure, bring the rolling shutter to the midpoint of its stroke.
01. Bring the rolling shutter to 5 cm from limit switch "1".
02. Keep the n key pressed and wait for the motor to perform 2 movements. Upon completion, release the key.
03. Keep the n key pressed again and wait for the motor to perform 4 movements. Upon completion, release the key.
13 – English
02
2
10
sec.
02
2
?
10
sec.
3
5
sec.
04
1 /
2 /
3 /
?
4 /
5 /
3
5
sec.
04
1 /
2 /
3 /
3
5
4 /
sec.
5 /
3
5
sec.
THE
END
END
THE
END
END