Spare Parts - Baltic 165N LIFEJACKETS Guía De Usuario

ENGLISH
REARMING BALTIC AUTOMATIC VERSION
Unscrew the used capsule anticlockwise
1.
by the inflation mechanism. Replace the capsule if it has been activated or if it has passed its
expiry date 6 , which is stamped on the side of the capsule. For example, 02 2015 means
it must be replaced before February 2015.
Refit the examined capsule if ok if not screw in a new capsule clockwise and tighten it by hand
2.
until no threads are visible. The lower indicator window on the valve head should now be green.
Unscrew the CO cylinder anticlockwise. Discard the cylinder in an environmentally friendly
3.
2
manner. Check that the lever and the pin (visible at the bottom of the valve head next to the
CO cylinder's fastening)
11:1
2
the lever and secure it by pressing it against the valve head until it clicks into place.
Visually check that the O-ring in the bottom of the valve head, next to the CO
4.
ning, is undamaged 11:2 .
Screw in a new, clean and unpierced CO
5.
Use no tools.
When both capsule and CO cylinder are mounted correctly, both indication windows should be green.
2
REARMING BALTIC MANUAL VERSION
Unscrew the CO cylinder anticlockwise. Discard the cylinder in an environmentally friendly
1.
2
manner. Check that the lever and the piercing pin (visible at the bottom of the thread for the
CO cylinder can move freely, by pulling on the activating cord. Fold back the lever and
11:1
2
secure it by pressing it against the valve head until it clicks into place.
12
Visually check that the O-ring in the bottom of the valve head, next to the CO
2.
ning, is undamaged 11:2 .
Screw in a new, clean and unpierced CO
3.
Use no tools.
When the CO cylinder is mounted correctly, the indicator window should be green.
2
REPACKING
BEFORE REPACKING
Follow these instructions carefully.
•
Repacking must be carried out with dry hands, in dry surroundings and without tools.
•
Place the inflatable lifejacket, back downwards, on a flat surface
•
Make sure the lifejacket is deflated and the mouth inflation tube's cap is in the normal position
•
and the indicator shows green.
10 , Follow the illustrated instructions on the label
can move freely, by pulling on the activating cord. Fold back
cylinder's faste-
2
cylinder using only hand force until absolutely tight.
2
cylinder's faste-
2
cylinder using only hand force until absolutely tight.
2
12 .
BA LT I C LIFEJAC KE T S - U S ER 'S GUI DE
Release the zip slider by pulling it to the end of the longer zip
1.
lifejacket. Pull the slider back clockwise, to the right hand side of the lifejacket.
Put the zip together like on a normal jacket 14
2.
lifejacket, at the same time folding the lung according to the instructions below.
Fold under in a Z-shape 15:1 .
3.
Fold under in a Z-shape 15:2 .
4.
Fold under 15:3 .
4.
Fold under in a Z-shape 16 .
6.
Fold under in a Z-shape 17:1 .
7.
Fold under in a Z-shape .
17:2
8.
Fold under 17:3 .
9.
The lifejacket is closed by pulling the slider round the lifejacket
10.
next to the two quick release openings 1 , 2
end-stop at the end of the zip 19 . Place the zip's end in the lifejacket
Make sure the activating cord is exposed by pushing it through the opening in the back of the
11.
outer cover before closing the lifejacket 3 .

SPARE PARTS

The following spare parts are available from Baltic retailers:
Rearming kit Baltic 33 g CO cylinder, Part No 2433. Includes 33 g CO
2
Capsule, Part No 2407. Includes automatic capsule.
Whistle
Reflector kit
Crutch strap kit 30 mm
ACCESSORIES
There are a number of accessories for inflatable lifejackets, which can be used in different situations.
These accessories are available through Baltic retailers.
Automatic emergency light
Sprayhood
Protective cover
Weld protection
The model name is written on the front of the product.
The date of manufacture is printed on the product's inspection history label.
13 , on the left hand side of the
, and pull the slider anticlockwise round the
18 . Secure the Velcro strip
. Take care to stop the slider at the first
20 .
cylinder.
2
13