Cooktop Use; Sealed Surface Burners - Whirlpool WFG515S0JW1 Manual De Uso

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

KEYPAD
FEATURE
START TIME
Delayed start
COOK TIME
Timed cooking
SELF CLEAN
Self-Cleaning
cycle
CONTROL
Oven control
LOCK
lockout
WARNING
Fire Hazard
Do not let the burner flame extend beyond the edge of
the pan.
Turn off all controls when not cooking.
Failure to follow these instructions can result in death
or fire.
Electric igniters automatically light the surface burners when
control knobs are turned to IGNITE.
Before setting a control knob, place fi lled cookware on the grate.
Do not operate a burner using empty cookware or without
cookware on the grate.
To Set:
1. Push in and turn knob counterclockwise to IGNITE.
All surface burners will click. Only the burner with the control
knob turned to IGNITE will produce a fl ame.
2. Turn knob to anywhere between HIGH and LOW.
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
Power Failure
In case of prolonged power failure, the surface burners can be lit
manually. Hold a lit match near a burner and turn knob
counterclockwise to IGNITE. After burner lights, turn knob to
setting.
INSTRUCTIONS
The Start Time keypad is used to enter the starting time for an oven function with a delayed start.
Start Time should not be used for foods such as breads and cakes because they may not bake
properly.
To set a Timed Cook or a Delayed Timed Cook, see "Cook Time" section.
Timed Cooking allows the oven to be set to turn on at a certain time of day, cook for a set length
of time, and/or shut off automatically.
To set a Timed Cook or a Delayed Timed Cook, see "Cook Time" section.
See the "Self-Cleaning Cycle" section.
1. Check that the oven is off.
2. Press and hold the CONTROL LOCK keypad for 3 seconds.
3. A tone will sound, and "Loc" will be displayed.
4. Repeat to unlock. Only the CLOCK, OVEN LIGHT and TIMER keypads will function with the
controls locked. The cooktop functions are not affected by the oven control lockout.

COOKTOP USE

Sealed Surface Burners

A
B
C
A. Burner cap
B. Burner base
IMPORTANT: Do not obstruct the fl ow of combustion and
ventilation air around the burner grate edges.
Burner Cap: Always keep the burner cap in place when using a
surface burner. A clean burner cap will help avoid poor ignition and
uneven fl ames. Always clean the burner cap after a spillover and
routinely remove and clean the caps according to the "General
Cleaning" section.
Alignment: Be sure to align the gas tube opening in the burner
base with the orifi ce holder on the cooktop and the igniter electrode
with the notch in the burner base.
Gas Tube Opening: Gas must fl ow freely throughout the gas tube
opening for the burner to light properly. Keep this area free of soil,
and do not allow spills, food, cleaning agents or any other material
to enter the gas tube opening. Keep spillovers out of the gas tube
by always using a burner cap.
A
1
A. 1 to 1
B. Burner ports
Burner Ports: Check burner fl ames occasionally for proper size
and shape as shown in the previous illustration. A good fl ame is
blue in color, not yellow. Keep this area free of soil and do not
allow spills, food, cleaning agents or any other material to enter the
burner ports.
E
D
C. Alignment pins
D. Igniter
E. Gas tube opening
B
/
" (2.5 to 3.8 cm)
2
5

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido