Memory Storing The Radio Code - Genius BRAIN 15 Instrucciones Para El Uso

Pagina 1 BRAIN 15
Guide for the installer
to execute learning. The BUS LED flashes.
6. Give an OPEN impulse, leaves will move and the BUS
learning procedure is over.
The board has memory stored the BUS accessories. Follow
the instructions in the table below to check if the BUS con-
nection is correct.
Tab. 6 - Description of BUS LED
Normal operation (LED ON even in
Steady light
the absence of photocells)
At least one input engaged: photo-
Slow flashing lamp
cell engaged or not aligned, Open A
(flash every 0.5 sec)
or Open B or Stop input engaged
Light OFF
BUS line short circuited
(flash every 2.5 sec)
If you have detected a BUS con-
nection error, repeat the acquisition
procedure. If the error is repeated,
Fast flashing lamp
make sure that there is not more
(flash every 0.2 sec)
than one accessory with the same
address in the system (also see the
accessories instructions)

8. MEMORY STORING THE RADIO CODE

The control board has an integrated 2-channel decoding
system. This system makes it possible to memory-store both
total opening (OPEN A) and partial opening OPEN B) of the
automated system - this is made possible by an additional
receiver module (fig.3 ref. a) and radio controls on the same
frequency.
• Only one radio code can be used at a time.
• To change over from one code to another, you
must delete the existing one (see paragraph
on deletion), and repeat the memory-storage
procedure.
8.1. Memory storage of 868 radio controls
A maximum of 250 codes can be memory stored,
split between OPEN A and OPEN B.
1. On the radio control, simultaneously press and hold
down push-buttons P1 and P2.
2. The radio control LED begins to flash.
3. Release both push-buttons.
4. Press the LOGIC (SW3) or SPEED (SW2) push-button, to
memory store respectively total opening (OPEN A) or
partial opening (OPEN B), and as you hold it down, also
press the SETUP (SW1) push-button. The relevant LED
starts to flash slowly for 5 sec.
5. Release both push-buttons.
6. Within these 5 sec., while the radio control LED is still
flashing, press and hold down the required push-button
on the radio control (the radio control LED lights up on
steady beam).
7. The LED on the board lights up on steady beam for 1
second and then goes OFF, indicating that storage
was executed.
8. Release the radio control push-button.
9. Quickly press twice the memory stored radio control
push-button.
The automated system performs one opening operation.
Make sure that the automated system is free of any
obstacle created by persons or things.
To add other radio controls, transfer the code of the me-
mory-stored push-button of the radio control to the relevant
push-button of the radio controls to be added, observing the
following procedure:
• On the memory stored radio control, simultaneously press
and hold down push-buttons P1 and P2.
• The radio control LED begins to flash.
• Release both push-buttons.
• Press the memory stored push-button and hold it down (the
radio control LED lights up on steady beam).
• Bring the radio controls near, press and hold down the
push-button of the radio control to be added, releasing it
only after the double flash of the radio control LED, which
indicates memory storage executed.
• Quickly press twice the push-button of the memory stored
radio control.
The automated system performs one opening operation.
Make sure that the automated system is free of any
obstacle created by persons or things.
8.2. Memory storage of 433 radio controls
A maximum of 250 codes can be memory stored,
split between OPEN A and OPEN B.
1. Use 433 remote controls only with receiver module
at 433 MHz.
Press the LOGIC (SW3) or SPEED (SW2) push-button, to
2.
memory store respectively total opening (OPEN A) or
partial opening (OPEN B), and as you hold it down, also
press the SETUP (SW1) push-button. The relevant LED
starts to flash slowly for 5 sec.
3. Release both push-buttons. Within these 5 sec., press the
appropriate push-button on the remote control.
4. The LED lights up on steady beam for 1 second, indi-
cating memory storage executed, and then resumes
flashing for another 5 sec., during which another radio
control (point 4) can be memory stored.
5. When the 5 sec. have elapsed, the LED goes OFF indi-
cating the end of the procedure.
To add other radio controls, repeat the operation at
6.
point 1.
Fig. 3
8.2.1. r
EMOTE MEMOry STOrAgE Of
Other radio controls can be remotely stored only with the 433
radio controls, i.e. without using the LOGIC-SPEED-SETUP push-
buttons, but using a previously stored radio control.
Get a radio control already stored on one of the 2
1.
channels (OPEN A or OPEN B ).
2. Press and hold down push-buttons P1 and P2 simulta-
neously until both the LEDs flash slowly for 5 sec.
3. Within 5 sec. press the push-button of the radio control
that had been memory stored to enable learning on
the selected channel.
4. The LED on the board relating to the channel being
learned flashes for 5 sec., within which time the code
of another radio control must be transmitted.
The LED lights up on steady beam for 2 seconds, indi-
5.
433
rAdIO CONTrOLS