Independent Operation Of Several Systems; Reset; System Reset (Using Master Remote); Reset Master Remote - Osram DALIeco Control Manual De Instrucciones

DALIeco Control

7.4 Independent operation of several systems

Teaching of the User Remote to a specifi c selected receiver in order to permit independent
operation of several systems (maximum 15) in the same room.
1. Simultaneously press push-buttons [CH-1
(VLP) to start individual programming (LED fl ashes red).
2. Activating number block (factory setting = 16):
- Number block 1-4: Press push-button [1] (SP).
- Number block 5-8: Press push-button [2] (SP).
- Number block 9-12: Press push-button [3] (SP).
- Number block 13-16: Press push-button [4] (SP).
3. Programming system number:
- Press push-button [1], [2], [3] or [4] (SP) for the system
number to be programmed (factory setting = 16) (LED
fl ashes green twice and system fl ashes in confi rmation).
--> Example: Programming system number 10:
1. Simultaneously press push-buttons [CH-1
2. Press push-button [3] (SP) to activate number block 9-12.
3. Press push-button [2] (SP) to program system number 10
(LED fl ashes green twice and system fl ashes in confi rmation).
8

Reset

8.1 System reset (using Master Remote)

1. Press push-button [PROG] (LP) to start programming mode (LED1 fl ashes).
2. Press [Single Offi ce] (SP) to set default function mode (LED1 fl ashes rapidly).
3. Press push-button [PROG] (SP) to exit programming mode.

8.2 Reset Master Remote

1. Press push-button [PROG] (LP) to start programming mode (LED1 fl ashes).
2. Simultaneously press (VLP) [Corridor] and [Staircase] (LED2 fl ashes).
3. Press push-button [PROG] (LP) – (LED1 and LED2 light up orange for 3 seconds).

8.3 Reset User Remote

1. Simultaneously press (VLP) [CH-1
2. Press push-button [4] (SP) – (LED lights up orange for 3 seconds).
31
] + [CH-2
] + [CH-2 ] (VLP) (LED fl ashes red).
] and [Resume] (LED fl ashes red).
9

Technical data

Mains connection
Push-button input
]
DALI interface (data for each channel)
Available DALI control current
Sensor interface
Max. line length
synchronization line / push-button input
Power consumption
Ambient temperature
Type of protection
Protection rating
Conformity
i Important notes:
• Push-button, sensor, and DALI lines must be routed separately from lamp and LED
module supply lines.
• If possible, push-button lines should not be routed together with the power supply
in the same cable.
• Route sensor lines separately from the power supply.
• With longer cable lengths or electromagnetic interference, it is recommended, that
expansion sensors or push-buttons be connected via the DALI line.
• To guarantee correct operation of the system new components may only be con-
nected and unclamped / unplugged while in a voltage-free condition.
GB
220 – 240 V AC 50-60 Hz
Floating NO contacts,
(see below under "Important notes")
Max. total cable length: 100 m
Max. 16 EVG + max. 3 DALI
Sensors or push-button couplers
Max. 64 mA on one channel
Max. 96 mA in total via both channels
Max. 4 DALIeco LS/PD LI or
4 DALIeco LS/PD LI NP or
1 HF LS LI Sensor
Max. total cable length
to all sensors: 25 m
50 m (in total)
0.2 W - 3.0 W (depending on
ECG/number of sensors)
-20 °C to +50 °C (operation)
IP20
II, protective insulation
CE