Display Type - Lutron QSE-CI-DMX Instrucciones De Instalación Y Operación

Programming
Note: For systems controlled by a Quantum system, all
programming is done using the Q-Design
programming section applies only to systems controlled using a
GRAFIK Eye QS control unit.
Assigning a Single DMX Channel to a
GRAFIK Eye QS Zone
Most DMX fixtures use single-channel assignment. If you are
using single-channel DMX, follow the instructions below. If
your DMX fixture has 3 channels (RGB or CMY), refer to the
instructions to the right for 3-channel DMX assignment.
1. Enter programming mode on the
Zone 4
GRAFIK Eye QS. Choose "Zone Setup"
then "Load Type" from the Main Menu.
Zone 4
For the zones you wish to assign to
DMX
DMX channels, change the load type
DMX to DMX.
2. Exit programming mode on the
DMX Prog
GRAFIK Eye QS.
Push
3. Enter programming mode on the
DMX Prog
Zone R to Assign
QSE-CI-DMX: Press and hold the
Zone L to Unassign
Push
programming button for 3 seconds.
Zone R to Assign
The "Status" LED will blink rapidly. On
Zone L to Unassign
any GRAFIK Eye QS control units on
Zone 4
the link, the zone LEDs will indicate
Choose Channel on
their status:
Zone 4
DMX AABB-CCEE
LEDs of assigned zones will go to full on (all LEDs lit) then flash,
Choose Channel on
14
and all LEDs of unassigned zones will go to Off. To assign a DMX
DMX AABB-CCEE
Channel to a zone, press "Zone Raise"; to unassign, press "Zone
14
Lower".
Zone 4
Zone 4
GRAFIK Eye QS control unit
Zone 4
Zone Buttons
RGB/CMY DMX
DMX
RGB/CMY DMX
1 9 2 10 3 11 4 12
Zone 4- RGB/CMY
DMX Prog
Zone 4- RGB/CMY
Component 1 channel
Push
Zone R to Assign
14
Zone L to Unassign
Component 1 channel
14
Zone 4
4. The GRAFIK Eye QS will display the
Zone 4
selected zone and an unassigned
Channels 1,2,3
Zone 4 Choose Channel on
DMX channel. Use the master buttons
on DMX AABB-CCDD
DMX AABB-CCEE
on the GRAFIK Eye QS to choose a
Channels 1,2,3
Unassign?
14
DMX channel (from 1 to 512) for this
on DMX AABB-CCDD
zone. Press the Scene 1 button on the
Unassign?

Display type

GRAFIK Eye QS to cause the currently
Zone 4
selected DMX channel to flash. Press
Set zones
Display type
OK to assign the selected DMX channel
to the selected zone.
RGB/CMY DMX
Set zones
Note: Do not use the Flash feature with DMX devices containing
moving parts (shade motors, motorized light fixtures, smoke-
producing machines, etc.) to avoid damaging those devices or High end
Zone 4- RGB/CMY
causing unexpected motion. If the selected channel is already
Set zones
assigned to a zone, the GRAFIK Eye QS will prompt you to High end
Component 1 channel
confirm replacing the channel with the new selection. Press OK
Set zones
to confirm the replacement.
14
RGB/CMY Config
Zone 4
Master R/L
RGB/CMY Config
Channels 1,2,3
on DMX AABB-CCDD
Enable
Master R/L
Unassign?
Enable
Display type
4
Set zones
software. This
TM
Zone LEDs full on and
flash (zone assigned to
5 13
QSE-CI-DMX)
Zone LEDs Off
(zone unassigned
to QSE-CI-DMX)
5. Repeat step 4 for each DMX zone.
6. Exit programming mode: Press and hold the programming
button on the QSE-CI-DMX for 3 seconds. The "Status" LED will
Zone 4
resume slow blinking (once per second).
Zone 4
DMX
DMX
DMX Prog
Push
OK
DMX Prog
Zone R to Assign
Zone L to Unassign
Push
Zone R to Assign
Zone L to Unassign
Zone 4
Choose Channel on
Zone 4
DMX AABB-CCEE
Choose Channel on
14
Assigning RGB/CMY DMX Channels
DMX AABB-CCEE
(3-Channel DMX) to GRAFIK Eye QS Zones
14
1. Enter programming mode on the
Zone 4
GRAFIK Eye QS. Choose "Zone Setup"
then "Load Type" from the Main Menu.
Zone 4
For the zones you wish to assign to
RGB/CMY DMX
RGB/CMY channels, change the load
type to RGB/CMY DMX.
RGB/CMY DMX
2. Exit programming mode on the
Zone 4- RGB/CMY
GRAFIK Eye QS.
3. Enter programming mode on the
Zone 4- RGB/CMY
Component 1 channel
QSE-CI-DMX: Press and hold the
14 programming button for 3 seconds.
Component 1 channel
The "Status" LED will blink rapidly.
14 On any GRAFIK Eye control units on
Zone 4
the link, the zone LEDs will indicate
their status: LEDs of assigned zones
Channels 1,2,3
Zone 4
will go to full on (all LEDs lit), and LEDs
on DMX AABB-CCDD
of unassigned zones will go to full off
Channels 1,2,3
Unassign?
(all LEDs off). To assign a DMX Channel
on DMX AABB-CCDD
to a zone, press "Zone Raise"; to
Unassign?
Display type
unassign, press "Zone Lower".
4. The GRAFIK Eye QS will display the selected zone and an
Set zones
Display type
unassigned DMX channel. Use the master buttons on the
GRAFIK Eye QS to choose a DMX component channel (from 1 to
Set zones
512) for this zone. Press the Scene 1 button on the GRAFIK Eye
QS to cause the currently selected DMX channel to flash. Press
High end
OK to assign the selected DMX channel to the selected zone and
proceed. Repeat for all 3 channels.
Set zones
High end
If the selected channel is already assigned to a zone, the GRAFIK
Eye QS will prompt you to confirm replacing the channel with the
Set zones
new selection. Press OK to confirm the replacement.
5. Repeat step 4 for all the RGB/CMY DMX zones.
RGB/CMY Config
6. Exit programming mode: Press and hold the programming
button on the QSE-CI-DMX for 3 seconds. The "Status" LED will
Master R/L
RGB/CMY Config
resume slow blinking (once per second).
Note: The RGB/CMY table can be edited to map a zone Enable
Master R/L
intensity to a specific RGB/CMY color using the color
Enable
configuration tool for the QSE-CI-DMX (available at
www.lutron.com/qs).
Master buttons
OK button
Timeclock (back) button
Scene 1 button