Customer Service - Peg-Perego John Deere POWER PULL Empleo Y Manutencion

• Verificare che non ci siano cavi scollegati dai
motoriduttori.
• Controllare il funzionamento del pulsante
dell'acceleratore ed eventualmente sostituirlo.
• Controllare che la batteria sia attaccata all'
impianto elettrico.
IL VEICOLO NON HA POTENZA?
• Caricare le batterie. Se dopo la ricarica il problema
persiste far controllare le batterie ed il
caricabatterie da un centro assistenza.
ENGLISH
•PEG PEREGO® thanks you for choosing this product.
For over 50 years, PEG PEREGO has been taking
children for an outing: first with its famous baby
carriages and strollers, later with its pedal and
battery operated toy vehicles.
•Read this instruction manual carefully to learn the
use of this vehicle and to teach your child safe and
enjoyable driving. Please keep this manual for use
as a reference in the future.
•Our toys conform with the safety requirements
provided by the Council of the EEC, of the T.Ü.V.; of
the I.I.S.G. Istituto Italiano Sicurezza Giocattoli, and
the U.S. Consumer Toy Safety Specification F963.
Peg Perego S.p.A. is an ISO 9001
certified company.
The fact that we are certified provides
a guarantee of our honesty for our
customers, and fosters trust in the
company's way of working.
•Peg Perego reserves the right to modify or change
their product. Price, literature, manufacturing
processes or locations or any combination of these
above mentioned entities may change at any time
for any reason without notice with impunity.
Years 3-8

CUSTOMER SERVICE

PEG PEREGO offers after-sales services, directly or
with a network of authorized service centers for
repairs or replacement parts. See the back cover of
this instruction manual for a list of service centers.
Peg Perego is at the consumer's service, meeting
every need in the best way possible. This is why our
customers' opinions are so important and valuable
to us. We would be very grateful if you would kindly
fill in the CUSTOMER SATISFACTION
QUESTIONNAIRE after using one of our products.
You will find the questionnaire on the Internet at
"www.pegperego.com/SSCo.html.en-UK".
Please note any observations or suggestions you
may have on the questionnaire.
ASSEMBLY INSTRUCTIONS
ADULT ASSEMBLY REQUIRED.
USE CARE WHEN UNPACKING AS COMPONENTS TO
BE ASSEMBLED MAY POSE A SMALL PARTS/SHARP
EDGE HAZARD.
BATTERY ALREADY INSTALLED IN VEHICLE.
ASSEMBLY
1-2 • Unscrew and remove the bottom of the trailer
from the bottom of the tractor.
3 • Insert one of the 4 self-locking washers (the
tractor comes with 2 spare washers) into the
special tool provided with the tractor.
ATTENTION: the tabs on the self-locking washer
must be turned towards the interior of the tool
(see detail A).
4 • Remove the axle from the packing. Remove the
protective caps from the axle. Insert the axle by
pounding the special tool all the way in using a
hammer. Remove the tool.
5 • Slip the following components onto the axle in
this order: washer, wheel, second wheel, washer
(four washers come with the tractor; two of
them are spares). ATTENTION: Check to make
sure that the wheels have been inserted
correctly on the axle. The hubcaps must be
turned outwards.
6 • Place a self-locking washer in the special tool,
and insert the prepared axle, pounding it all the
way in.
7 • Attach the wheel unit to the base of the trailer
by pressing on it.
8 • Insert the red pin into the end of the trailer.
9 • Remove the three protective caps from the
bottom of the bed.
10 • Attach the sides of the bed by inserting the
longest pin first.
11 • Finish inserting the sides of the bed by pressing
on the short pin.
12 • Lift the sides to close the bed.
13 • Attach the bottom of the trailer (prepared
beforehand) to the bed by pressing, as shown
in the figure.
14 • Attach the 2 hubcaps to the wheels on the
trailer (Attention, in the packaging you will find
6 hubcaps; the remaining 4 are to be attached
to the wheels of the tractor).
15 • Attach the plastic drop to the hood, as shown
in the figure.
16 • Apply the stickers to the special areas on the
front headlights.
17 • Position the headlight glass by attaching the
outer side.
18 • Press as shown in the figure to snap the glass
into place.
19 • Repeat this step for the other front headlight.
20 • Position one of the two parts of the weight on
the front of the tractor.
21 • Join the other part of the weight by pressing
the two parts together.
22 • Insert the pin into the special opening in the
weight.
23 • Push the pin all the way in.
24 • Press the side inserts into place on the body.
25 • Press the ring nut into place under the steering
wheel.
26 • Push the steering column through the bottom
of the tractor to the upper part of the body.
27 • Hold the column in place and slip the steering
wheel onto it.
28 • Fasten the steering wheel with its screw and
nut, being careful to insert the screw into the
circular hole and to screw the nut onto the
hexagonal part.
29 • Apply the stickers to the special areas on the
rear headlights as shown in the figure.
30 • Attach the headlights by pressing from the
bottom upwards.
31 • Remove the seat support.
32 • Unscrew the knobs on the bottom of the seat.
33 • Line the seat up with the two holes on the seat
support.
34 • The seat can be adjusted to 2 positions to suit
the height of the child (see figure).
35 • After adjusting the seat, tighten the 2 knobs
that hold it in place.
36 • Reposition the seat support on the body of the
tractor and tighten the 2 screws.
37 • Position the roll bar (see figure).
38 • Push the roll bar all the way in.
39 • Tighten the 2 lock screws.
40 • Press the gas tank cap into place on the back of
the tractor.
41 • Attach the trailer to the tractor as follows: insert
the trailer coupling into the opening on the
back of the tractor, and rotate it (see fig. 42).
42 • Position 1: the trailer can be removed.
Position 2: the trailer is locked into place.
WARNING: The trailer will hold a load weighing
up to 10 kg.
43 • Loosen the two safety screws from the sides of
the cab, and remove the two plastic disks (save
the disks for putting the cab back on).
44 • Press the two buttons and at the same time
widen the cab to detach it, as shown in the
figure.
45 • Lift the cab off.
46 • Connect the battery plug to the electrical
system.
47 • Reposition the cab by inserting the front hook
into the opening on the bottom of the tractor
(see detail).
48 • Slightly widen the cab, and lower it to its
original position. Replace the two plastic disks
and fasten everything down with the screws.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
49 • GEAR SHIFT LEVER. The vehicle has 3 speeds.
ATTENTION: when the vehicle is taken out of
the packing, it runs only in first gear and
reverse gear. To use the second speed, follow
the instructions in figure 50.
50 • Loosen the lock screw for the second speed
(fig. A). Turn the lock screw to the next notch
(fig. B), and tighten it. All of the gears are now
ready for use.
51 • ACCELERATOR PEDAL/ELECTRIC BRAKE. When
the foot is lifted from the accelerator pedal, the
electric brake automatically stops the tractor.
REPLACING THE BATTERY
52 • Unscrew the two safety screws from the cab.
Remove the cab. Disconnect the battery from
the electrical system and loosen the 2 screws
on the battery brace, as shown in the figure.
53 • Extract the battery.
54 • Remove the battery clamp from the dead
battery and put it on the new battery.
55 • If you have bought or own a Peg Perego
12V/12Ah battery, you will have to remove the
plastic filler (A) by slipping it off the battery
clamp.
56 • Reposition the new battery with the battery
clamp in its housing. Fasten the clamp with the
two screws. Connect the battery plugs to the