Height Adjustment - Gemini UMX-7 Manual De Funcionamiento

Mezclador vca para el profesional

Ocultar thumbs

Contenido

página de 16

/ 16
Contenido
Tabla de contenido
Marcadores

Tabla de contenido

Idiomas disponibles

I n t r o d u c t i o n

Congratulations on purchasing the Gemini UMX-7 VCA mixer. This state

of the art mixer is backed by a three year warranty, excluding crossfader

and channel slides. Prior to use, we suggest that you carefully read all the

instructions.

With VCA technology, audio is processed in a voltage-controlled amplifier

(VCA) removing it from the crossfader and channel slides giving them

extended life and reducing travel noise. The crossfader and channel slides

regulate the DC voltage that controls the VCA circuit. Additional

advantages of VCA technology include the ability to provide precise curve

adjustments for the crossfader and channel slides without sacrificing audio

quality. For additional information, refer to the diagrams on Page 3 for

crossfader adjustment and channel slide curve.

Features

• 2 Stereo Channels

• State of the Art Cue Section with Split

• 3 Phono/Line Convertible, 1 Line, and 1 Mic Input

• Adjustable Input Assign Switches

• Channel Slide Curve Control

• Crossfader with Curve Control

• Crossfader Reverse (Hamster) Switch

• Cut Feature for Low, Mid and High for each channel

• Gain, High, Mid and Low tone controls for each channel

• Mic loop

• Talkover

• Balanced and Unbalanced Master Outputs

• Zone and Record outputs

• Dual mode display

Cautions

1 . All operating instructions should be read before using this equipment.

2 . To reduce the risk of electrical shock, do not open the unit. There are

NO USER REPLACEABLE PARTS INSIDE. Please refer servicing to a

qualified service technician.

In the U.S.A., if you have any problems with this unit, call

1-732-969-9000 for customer service. Do not return equipment

1-732-738-9003

to your dealer.

3 . Do not expose this unit to direct sunlight or to a heat source such as a

radiator or stove.

4 . This unit should be cleaned only with a damp cloth. Avoid solvents or

other cleaning detergents.

5 . When moving this equipment, it should be placed in its original carton

and packaging. This will reduce the risk of damage during transit.

6 . DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

7 . DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY

CONTROLS OR SWITCHES.

Height Adjustment

When using a UMX mixer with professional turntables, such

as the Gemini PT Series, you can make the mixer level with

the turntable by removing the mixer's feet.

1 . Place a small screw driver under the foot's center anchor.

2 . Gently pry the center anchor up and the foot will come off.

To replace the foot:

1 . Place the foot on the mixer without the center anchor.

2 . Replace the center anchor and push down on it to anchor the foot to

the mixer.

Connections

1 . Make sure that the POWER (1)

POWER (1)

POWER (1) switch is in the off position. This unit

POWER (1)

comes supplied with a 18 volt AC adaptor. Plug the adaptor into the

rear panel power jack. Then plug the adaptor into a proper power

source.

2 . The UMX-7 is supplied with 4 sets of output jacks. The BALANCED

MASTER OUTPUT (4)

MASTER OUTPUT (4) jacks are used to connect to your main

MASTER OUTPUT (4)

amplifier using standard cables with 1/4" connectors. We recommend

using the balanced amp outputs if the cables to your amp are 25 feet or

more. BALANCED MASTER OUTPUTS

BALANCED MASTER OUTPUTS have three separate

BALANCED MASTER OUTPUTS

conductors, two of which are signal (positive and negative) and one

shield (ground). The balanced line uses a tip-ring-sleeve connection.

Tip = hot or positive (+), ring = cold or negative (-), and sleeve =

shield/ground. The MASTER OUTPUT (5)

used to connect to your main amplifier. The REC OUTPUT (7)

can be used to connect the mixer to the record input of your recorder

enabling you to record your mix. The ZONE OUTPUT (6)

you to hook up an additional amplifier.

3 . For your convenience, there are 2 mic inputs (located on the front panel

and the rear panel), however, only one mic input can be used at a time.

The MIC (3)

MIC (3)

MIC (3) input (found on the rear panel) OR

MIC (3)

(found on the front panel) accepts a 1/4" connector and balanced and

unbalanced microphones. The MIC LOOP (14)

and input for connection to an outboard signal enhancer (such as a key

controller, echo/reverb machine, etc...) using a standard balanced cable

with a 1/4" tip/ring/sleeve connector (tip = in, ring = out, and sleeve

= shield/ground).

4 . On the rear panel are 3 stereo PHONO/LINE (9, 12, 13)

LINE (8)

stereo LINE (8)

LINE (8) input. The PHONO/LINE

LINE (8)

set the (9)

(9)

(9) input to Phono or Line. The PHONO/LINE

enables you to set the (12)

SWITCH (15)

SWITCH

(15) enables you to set the (13)

(15)

phono inputs will accept only turntables with a magnetic cartridge.

GROUND SCREWS (2)

GROUND SCREWS (2) for you to ground your turntables are located

GROUND SCREWS (2)

on the rear panel. The stereo line inputs will accept any line level input

such as a CD player, a cassette player, etc.

5 . Headphones can be plugged into the front panel mounted PHONES

( 4 3 )

( 4 3 ) j a c k .

( 4 3 )

Operation

1 . POWER ON: Once you have made all the equipment connections to

your mixer, press the POWER (1)

2 . CHANNEL 1: The GAIN (17), HIGH (20), MID (23), LOW (26),

GAIN (17), HIGH (20), MID (23), LOW (26),

GAIN (17), HIGH (20), MID (23), LOW (26), and

PAN (29)

PAN (29) controls allow you to fully adjust the selected source. Switch

PAN (29)

# (31)

(31) allows you to select the LINE 1/PHONO 1 (13)

(31)

PHONO 2 (12) input. The CHANNEL

PHONO 2 (12)

level of this channel.

3 . CHANNEL 2: The GAIN (17), HIGH (20), MID (23), LOW (26),

GAIN (17), HIGH (20), MID (23), LOW (26), and

GAIN (17), HIGH (20), MID (23), LOW (26),

PAN (29)

PAN (29) controls allow you to fully adjust the selected source. Switch

PAN (29)

(32)

# (32)

(32)

(32) allows you to select the LINE 3/PHONO 3 (9)

input. The CHANNEL

CHANNEL SLIDE

CHANNEL

SLIDE (39)

SLIDE

channel.

4 . TONE CONTROLS: There is Low, Mid and High equalization for each

channel with an extremely wide range of adjustment. SUGGESTION:

You can use the Cut Features on each channel to remove Low, Mid

and/or High to create special effects.

5 . INPUT ASSIGN SWITCHES: You can adjust the position of the INPUT

ASSIGN (31, 32)

ASSIGN (31, 32) switches to move left to right, up and down OR

45 degree angle. Make these adjustments with the power OFF.

P a g e

MASTER OUTPUT (5)

MASTER OUTPUT (5) jacks are unbalanced and

MASTER OUTPUT (5)

REC OUTPUT (7)

REC OUTPUT (7) jacks

ZONE OUTPUT (6)

ZONE OUTPUT (6) jacks allow

OR the MIC (42)

MIC (42) input

MIC (42)

MIC LOOP (14) jack acts as an output

MIC LOOP (14)

PHONO/LINE (9, 12, 13)

PHONO/LINE (9, 12, 13) inputs and 1

PHONO/LINE

SWITCH

(10)

PHONO/LINE

PHONO/LINE SWITCH

SWITCH

SWITCH (10)

(10) enables you to

(10)

PHONO/LINE

PHONO/LINE SWITCH

PHONO/LINE

(12)

(12) input to Phono or Line. The PHONO/LINE

(12)

(13)

(13) input to Phono or Line. The

(13)

POWER (1) switch.

POWER (1)

LINE 1/PHONO 1 (13) or the LINE 2/

LINE 1/PHONO 1 (13)

CHANNEL

CHANNEL SLIDE

CHANNEL

SLIDE

SLIDE (38)

SLIDE

(38)

(38) controls the input

LINE 3/PHONO 3 (9)

LINE 3/PHONO 3 (9) or the LINE 4 (8)

(39) controls the input level of this

(39)

BALANCED

SWITCH

SWITCH (11)

SWITCH

(11)

PHONO/LINE

PHONES

LINE 2/

LINE 4 (8)

INPUT

OR at a

Tabla de Contenido

Tabla de contenido

Height Adjustment - Gemini UMX-7 Manual De Funcionamiento

Idiomas disponibles

Height Adjustment

Manuales relacionados para Gemini UMX-7

Contenido relacionado para Gemini UMX-7

Tabla de contenido