Gemini CDJ-10 Manual De Funcionamiento página 3

INTRODUCTION
Congratulations on purchasing a Gemini CDJ-10 CD Player. This state of
the art professional CD player is backed by a three year warranty,
excluding lasers. One year warranty on CD lasers. Prior to use, we
suggest that you carefully read all the instructions.
CAUTIONS
Do not use this CD Player at temperatures below 41°F/5°C or higher
than 95°F/35°C.
Place the unit in a clean and dry location.
Do not place the unit in an unstable location.
When disconnecting the power cord from an AC outlet, always grasp it
by the plug. Never pull the power cord.
To prevent electric shock, do not remove the cover or the bottom screws.
There are no user serviceable parts inside. Please refer servicing to a
qualified technician.
Do not use chemical solvents to clean the unit.
Keep the laser pickup clean by keeping the tray closed.
Keep this manual in a safe place for future reference.
SAFETY CERTIFICATIONS
Laser Diode Properties
Material: Ga - Al - As
Wavelength: 755 - 815 nm (25° C)
Laser Output: Continuous Wave, max. 0.5mW
LINE VOLTAGE SELECTION
Model CDJ-10 is a dual voltage unit. It will operate at 115 or 230 volts. To
set the proper voltage follow these steps:
1. Place the head of a screw driver in the center of the VOLTAGE
SELECTOR SLIDE SWITCH (3) found on the rear panel.
2. Slide the switch left for 115 volts or push the switch right for 230 volts.
3. Do not force or twist the switch. Excessive force may cause damage.
If the switch does not move smoothly, contact a qualified technician.
CONNECTIONS
1. Plug one end of a set of RCA connectors into each of the LINE
OUTPUT JACKS (1).
2. Plug the other end of the RCA connectors into any available line level
input jacks on your mixer. If you are playing the CDJ-10 through a
receiver, you can plug the RCA connectors into the CD or AUX input
jacks on your receiver. If there are no CD or AUX inputs, use any line
level (not phono) inputs.
FUNCTION DESCRIPTIONS
POWER SWITCH: After making sure that the VOLTAGE SELECTOR
SLIDE SWITCH (3), found on the rear panel, is properly set, plug the
unit in and press the POWER SWITCH (2). The unit will turn on.
Pushing the POWER SWITCH (2) a second time will turn the unit off.
DISC TRAY: The DISC TRAY (10) is where the CD is held. Pressing the
disc tray OPEN BUTTON (16) will open the tray.
OPEN BUTTON: Press the OPEN BUTTON (16) to open the DISC
TRAY (3).
DISPLAY: The DISPLAY (4) shows the track numbers, play mode, pause
mode, and 3 different time displays. These time displays are time
elapsed on the track, time remaining on the disc and time remaining
on the track.
PLAYBACK DISPLAY: The PLAYBACK DISPLAY (5) displays the time
remaining to play and flashes slowly when the track has 30 seconds
left. The PLAYBACK DISPLAY (5) flashes quickly when the track
has 15 seconds left.
PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (9)
causes the operation to change from play to pause or from pause
back to play. See the CUE INSTRUCTIONS section for more
information.
TRACK SKIP : The TRACK SKIP BUTTONS (6) let you select
the track to play.
SEARCH BUTTONS
to move foward or reverse while in play mode. The SEARCH
BUTTONS (7) are also used to accurately position the disc at the
point where you wish the track to start playing. This position on the
track is memorized as the cue point. See the CUE INSTRUCTIONS
section for more information.
STOP : The STOP BUTTON (11) will end the playing of the CD.
TIME: The TIME BUTTON (12) switches the time display between the
three available choices listed under DISPLAY.
CUE: With the unit in the play mode, and after memorizing the cue point,
pressing the CUE BUTTON (8) will cause the CD player to enter the
pause mode at the memorized cue point. Holding down the cue
button changes the cue function to preview (allowing you to hear the
music play from the cue point) and releasing the cue button returns
you to the preset cue point. If a cue point is not memorized, pressing
the CUE BUTTON (8) will cause the unit to return to the beginning of
that track.
PITCH: Pushing the PITCH BUTTON (14) activates the pitch section of
the unit. The pitch of the CD will change according to the position of
the PITCH CONTROL (15).
CONTINUOUS: The CONTINUOUS (13) function will cause the unit to
play continuously (after the last track, the unit will return to the first
track of the disc and continue to play).
OPERATING INSTRUCTIONS
1. Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (3),
found on the rear panel, is set for the proper voltage. Plug the unit in
and press the POWER SWITCH (2).
2. Press the OPEN BUTTON (16), place a CD in the DISC TRAY (10)
and close the tray door. The display will initially show the number of
tracks and the total time of the CD.
3. Push the TRACK SKIP BUTTONS (6) to select the track you want to
play.
4. Press the PLAY/PAUSE BUTTON (9) and the unit will instantly play.
CUE INSTRUCTIONS
1. To start the play at a point other than the beginning of a track, follow
these instructions:
First choose the track you wish to play, and then press the PLAY/
PAUSE BUTTON (9) so the unit goes into the play mode. Press the
PLAY/PAUSE BUTTON (9) to pause play at the spot where you want
the play to start, the CUE POINT. Use the SCAN BUTTONS (8) to
pick the precise spot you want play to begin, then press the PLAY/
PAUSE BUTTON (9) again to save the cue point. Press the CUE
BUTTON (8) to pause play at the cue point (the unit will go into the
pause mode and the location indicated on the display will be the
memorized cue point). You can preview the cue point by pressing
and holding down the CUE BUTTON (8). Press the PLAY/PAUSE
BUTTON (9) to begin play from the cue point.
Note: After a cue point is set, pressing the TRACK SKIP BUTTONS
(6) clears the cue point. When you press the CUE BUTTON (8) in
the new track, the beginning of that track will be the new cue
point.
2. Once you have saved a cue point you can fine tune or change the
memorized cue point:
To change a cue point, push the PLAY/PAUSE BUTTON (9) so the
unit plays from the cue point, then press the PLAY/PAUSE BUTTON
(9) at the spot you wish your new cue point to be. Press the PLAY/
PAUSE BUTTON (9) again to save the cue point. The unit will go into
the pause mode and the location indicated on the display will be the
new memorized cue point.
Page 3
: The SEARCH BUTTONS (7) are used