Best IP29M Serie Manual Del Usaurio página 15

21. OPERATION
(CONT'D)
E
RASE LINK PROCESS
A. A " "
CTIVATE THE LINK
Push the LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds; the LinkLogic icon of the interface (item 11
on control illustration) should be visible and backlighting is full intensity at that point.
B. E L
RASE ALL LINKED
Push the LinkLogic erase link push-button (item 3 on control illustration) for 2 seconds to start the "Erase Link" process, flashing "E"
should be visible (item 8 on control illustration) on the hood interface until links are erased.
C. E " "
XIT LINK MODE OF THE HOOD
Press and hold LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds to exit "link" mode. Link mode remains
activated for 4 minutes if no other operation is done.
NOTE: If during normal operation of the range hood, the LinkLogic Icon (item 11 on control illustration) starts blinking, an error occurred
while communicating with a linked LinkLogic device. To reset this error flag, customer needs to enter and exit the Linking mode
as explained previously. This will erase the error flag until it happens again. If the problem happens again, it is recommended
to erase all links and start back the whole linking process.
22. LINKLOGIC SYSTEM CONTROL BOARD JUMPERS
The LinkLogic system is designed to work with devices like the Broan Smart Sense Fan system that requires CFM output or this range
hood. If you are using this hood with a LinkLogic device that requires CFM information, please follow the simple instruction/matrix below
to configure the LinkLogic control board in the hood to provide the correct CFM information. To access the LinkLogic control board, remove
baffle filters, grease drip rail and hood pan (see steps 5 and 6). Remove both screws retaining the control panel to the hood. Rotate
carefully the control panel in order to see the LinkLogic board jumpers. Remove jumpers from current location on pins and reconfigure
based on blower performance.
3
2
1
HE0089
L L
INK OGIC BOARD JUMPERS
If you are unsure if the LinkLogic accessory or device requires CFM data, please refer to the unit's instructions.
WARRANTY
Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of Best products that such products will be free from
defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT ABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be
defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND INCANDESCENT BULBS,
FUSES, FILTERS, DUCTS, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a)
normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states or provinces do
not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE'S OPTION, SHALL BE THE
PURCHASER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR
PERFORMANCE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to another.
This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone at the address stated below or telephone number
stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time
of requesting warranty service, you must present evidence of the original purchase date.
In USA - Best ® , 926 W. State Street, Hartford, WI 53027 (800-558-1711)
In Canada - Best ® , 550 Lemire Blvd., Drummondville, QC, Canada, J2C 7W9 (866-737-7770)
MODE OF THE HOOD
L
INK OGIC DEVICES
Pin 1 Pin 2 Pin 3 Maximum CFM value
0
0
0
0
0 = No jumper on pin.
1 = Jumper on pin.
ONE-YEAR LIMITED WARRANTY FOR BEST PRODUCTS
0 0 0 CFM
0 1 300 CFM
1 0 500 CFM
1 1 600 CFM
WARRANTY
www.BestRangeHoods.com
- 15 -
Pin 1 Pin 2 Pin 3 Maximum CFM value
1 0 0 900 CFM
1 0 1 1000 CFM
1 1 0 1200 CFM
1 1 1 1500 CFM
0 = No jumper on pin.
1 = Jumper on pin.