Driving The Machine; Work Method; Battery Charge Level Controls; Direct Scrubbing Or For Slightly Dirty Surfaces - LAVOR Pro SPEED 45E Manual Del Usaurio

7.13 DRIVING THE MACHINE

Model AC 230V
- Connect the power cable of the machine ( Photo
6 - B ) to the power mains using a patch cord.
- Switch ON the general ON-OFF switch ( Photo 5 -
B ).
- Switch ON the brush motor switch ( Photo 5 - C )
!
( ) The brush will start the rotation only
when the operator will pull the brush opera-
tion lever ( Photo 2 - A ).
- Switch ON the suction motor switch ( Photo 5 - A ).
- Open the solution water valve rotating the lever (
Photo 4 - B )( Photo 33 ).
- Lower the squeegee unit by using the lift/lower
lever ( Photo 4 - A ).
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo 2 - A ) to start the
brush rotation and the solution water outlet; re-
leasing the lever the brush rotation will stop after
few seconds.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.
Model DC 24V
- Put the ignition key ( Photo 7 - E ) in and turn ON
the machine.
- Check the battery charge status on the battery
power test placed on the control panel ( Photo 7 -
D ).
- Switch ON the brush motor switch ( Photo 7 - C )
!
( ) The brush will start the rotation only
when the operator will pull the brush opera-
tion lever ( Photo 2 - A ).
- Switch ON the suction motor switch ( Photo 7 - A
).
- Open the solution water valve rotating the lever (
Photo 4 - B )( Photo 33 ).
- Lower the squeegee unit by using the lift/lower
lever ( Photo 4 - A ).
- Wash the floor moving forward slowly, pulling the
brush operation lever ( Photo 2 - A ) to start the
brush rotation and the solution water outlet; re-
leasing the lever the brush rotation will stop after
few seconds.
!
( ) Remember to lift the squeegee before driving
reverse to avoid damaging it.

7.14 WORK METHOD

7.14.1 PREPARATION AND WARNINGS
Remove any loose solid residue from the surface to
be treated (using suitable tools, such as vacuum
cleaners, sweepers, etc.). It this is not done, the
solid dirt might prevent the squeegee from operat-
ing correctly, reducing drying efficiency.
Only trained personnel can drive this machine.
7 - OPERATING INFORMATIONS

7.14.2 BATTERY CHARGE LEVEL CONTROLS

The sequence of lights of the battery power test (
Photo 7 - D ) shows the battery discharging (green
light = battery fully charged; yellow light = battery
half charged; red light = battery discharged). When
the red light turns on, turn off the brush motor,
close the detergent solution outlet, finish drying the
small residual moisture and go to the battery charg-
ing area to charge the battery.
!
( ) The battery may be irreparably damaged
if the residual charge level drops too low (see
the battery operating manual). Do not force
the battery discharge beyond the safety lim-
its, turning the key off and on or in any other
manner.
7.14.3 DIRECT
SLIGHTLY DIRTY SURFACES
Scrubbing and drying in a single pass.
Prepare the machine as previously described and
use it as described in paragraph 7.13 .
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.
7.14.4 INDIRECT SCRUBBING OR FOR VERY
DIRTY SURFACES
Scrubbing and drying in various passes.
Prepare the machine as previously described.
First set of operations:
Wash the floor as described in paragraph 7.13 with-
out drying the floor
Allow the detergent solution to work on the
dirty floor according to what is indicated in
the information relative to the detergent
used.
Second set of operations:
Proceed as explained in the previous "Direct Wash-
ing" paragraph (7.14.3) to also proceed with dry-
ing the floor.
☞
( ) Never use the machine without the detergent
solution: the floor might be damaged.

7.14.5 POST-SCRUBBING OPERATIONS

Close the detergent solution outlet.
After having completely dried any traces of water
on the surface, wait a few seconds and then lift the
squeegee and turn off the suction motor.
Move to a suitable location to drain the tanks;
empty and clean the tanks (see 7.10).
Turn OFF the machine and remove the ignition key
from the control panel.
If necessary, charge the battery (see the relative
section).
46
SCRUBBING OR FOR