Índice De Palabras Clave - Sew Eurodrive MOVIAXIS MXR81A Manual De Instrucciones

Índice de palabras clave
Índice de palabras clave
0...9
10467.12 Ud .......................................................44
10467.13 Uq .......................................................44
10467.14 Ud setpoint ..........................................42
10467.15 Uq setpoint ..........................................42
10467.16 Ualpha .................................................44
10467.17 Ubeta ..................................................44
10467.2 Uz setpoint ............................................46
10467.3 Ialpha ....................................................44
10467.4 Ibeta ......................................................44
10467.40 Effective power ....................................42
10467.41 Regenerated energy ...........................42
10467.42 Filtered effective power .......................42
10467.50 Id .........................................................44
10467.51 Iq .........................................................44
10467.8 Id setpoint .............................................42
10467.9 Iq setpoint .............................................42
10469.4 Power-off tolerance ...............................45
10470.10 Line frequency .....................................45
10470.14 Line voltage .........................................45
10470.4 Control settings (modo de
funcionamiento) ...................................................45
10472.1 Charging timeout monitoring .................45
10472.11 Timeout when opening the line
contactor .............................................................45
10472.7 Test and emergency mode ...................45
10483.2 Configured device power ......................43
8325.0 DC link voltage ........................................42
8326.0 Filtered output current .............................42
8334.0 / 8334.1 / 8349.0 / 8349.1 / 9559.3 /
9559.4 I/O basic unit ...........................................49
9514.1 CAN1 / 9515.1 CAN2 / 9516.1
Communication option data source .....................46
9514.14 CAN1 / 9515.14 CAN2 Data
acceptance with sync ..........................................47
9514.14 CAN1 / 9515.14 CAN2 nEndianess ......47
9514.16 CAN1 / 9515.16 CAN2 / 9516.16
Communication option ........................................46
9514.19 CAN1 / 9515.19 CAN2 / 9516.19
Communication option ........................................46
9514.2 CAN1 / 9515.2 CAN2 message ID ..........46
9514.3 CAN1 / 9515.3 CAN2 / 9516.3
Communication option ........................................46
9514.4 CAN1 / 9515.4 CAN2 / 9516.4
Communication option ........................................46
9514.5 CAN1 / 9515.5 CAN2 / 9516.5
Communication option ........................................46
9563.1 CAN1 / 9564.1 CAN2 Send
PDO after sync ....................................................47
96
9563.16 CAN1 / 9564.16 CAN2 / 9565.16
Communication option configuration error ......... 47
9563.17 CAN1 / 9564.17 CAN2 blocking time ... 47
9563.19 CAN1 / 9564.19 CAN2 Send PDO
following receipt of IN-PDO ................................ 48
9563.2 CAN1 / 9564.2 CAN2 Send PDO
cyclically ............................................................. 48
9563.21 CAN1 / 9564.21 CAN2 endianess ........ 47
9563.22 CAN1 / 9564.22 CAN2 Send PDO
after n sync ......................................................... 48
9563.23 CAN1 / 9564.23 CAN2 Send PDO
following change ................................................ 48
9563.3 CAN1 / 9564.3 CAN2 / 9565.3
Communication option data sink ........................ 47
9563.4 CAN1 / 9564.4 CAN2 message ID ......... 47
9563.5 CAN1 / 9564.5 CAN2 / 9565.5
Communication option data block start .............. 47
9563.6 CAN1 / 9564.6 CAN2 / 9565.6
Communication option data block length ........... 47
9786.1 Output current ........................................ 42
9795.1 Heat sink temperature ............................ 43
9811.1 Dynamic utilization chip hub ................... 43
9811.3 Electromechanical utilization .................. 43
9811.4 Heat sink utilization ................................ 43
9811.5 Total utilization ....................................... 43
9856.2 CAN1 / 9856.3 CAN2 Layout ................. 48
9859.1 Thermal current limit .............................. 43
A
Accesorios .......................................................... 16
Accesorios de serie ............................................ 16
Asignación de bornas en MXR ........................... 27
Asignación de los datos de proceso en caso
de funcionamiento con bus de campo ............... 39
B
Bus de campo
EtherCAT ..................................................... 33
Bus de sistema
CAN ............................................................. 30
EtherCAT ..................................................... 32
C
Cableado
Conexiones de potencia .............................. 24
Combinación MXR con otros aparatos ............... 15
Compatibilidad electromagnética (CEM)
Categorías de emisión de interferencias ..... 75
Emisión de interferencias ............................ 75
Resistencia a interferencias ......................... 75
Módulo de alimentación regenerativo, en forma de bloque –
Servocontrolador de ejes múltiples MOVIAXIS
®