Tabla de contenido
Publicidad
DESCRIPTION OF INDICATORS ON THE CONTROL PANEL:
In general, the following guidelines apply to the control panel indicators:
A steady red indicator means that the function is inhibited for some reason.
A flashing red indicator means that a fault has occurred in the particular system. An example of this would be an over-current fault.
A yellow indicator means that the particular function has been enabled but is not currently on. For example, if a scrub mode is selected and the Drive Paddle (3)
is in neutral, the scrub system, vacuum, and solution indicators will all be yellow indicating that the systems are enabled and ready to turn on when the Drive Paddle
(3) is moved to forward or reverse.
A green indicator means that the particular system is on.
A flashing green indicator means that the particular system is in a delayed-off condition. An example of this is when a scrub mode is selected and the Drive Paddle
(3) goes from forward or reverse to neutral. When this happens the vacuum indicator will flash green indicating that the vacuum is still on but that it will be turning
off after the delay period.
Main Power Indicator (19):
•
This indicator will be GREEN when the key switch is ON.
•
This indicator will flash RED if there is a system fault that requires turning the Master ON/OFF Key Switch (20) off to reset.
•
This indicator will flash fault codes from the Curtis Speed Control if a fault exists. This will be accompanied by an "Err03" indication on the Hourmeter/
Status Display (18).
Solution System Indicator (21):
•
This indicator will be YELLOW if the solution system is in the AUTO mode and the Drive Paddle (3) is in the neutral position. This indicates that the solution
system is enabled but the solution flow is currently off.
•
This indicator will be GREEN if the solution system is in the AUTO mode and the Drive Paddle (3) is in the forward or reverse position. It will also be GREEN
if the solution system is in the MOMENTARY ON mode. This indicates that the solution flow is currently on.
•
This indicator will be OFF if the solution system is in the OFF mode.
Solution System Fault Indicator (22):
•
This indicator will flash red if there is a fault in the solution system. This will be accompanied by an error indication on the Hour Meter / Status Display
(18).
Vacuum System Fault Indicator (24):
•
This indicator will flash red if there is a fault in the vacuum or squeegee systems. This will be accompanied by an error indication on the Hour Meter / Status
Display (18).
•
This indicator will be RED and the Hour Meter / Status Display (18) will show "FULL" if the recovery tank float valve has closed. If this indication occurs
and the tank is not full, see the Troubleshooting section.
Vacuum System Indicator (26):
•
This indicator will be YELLOW if the vacuum/squeegee system is in the AUTO mode and the Drive Paddle (3) is in the neutral position. This indicates
that the vacuum system is enabled but the vacuum is currently off.
•
This indicator will be GREEN if the vacuum is currently on. This indicates that the system is in the AUTO mode and the Drive Paddle (3) is not in neutral
or that the vacuum system is in the ON mode.
•
This indicator will FLASH GREEN if the shutoff delay is keeping the vacuum on. This occurs if the vacuum system is in the AUTO mode and the Drive
Paddle (3) goes to the neutral position. This will also occur if the vacuum system is turned off while it was in either the AUTO or ON modes. The shutoff
delay will turn the vacuum off after the delay period.
•
This indicator will be OFF if the vacuum/squeegee system if in the OFF mode.
Heavy Scrub Mode Indicator (28):
•
This indicator will be YELLOW if the heavy scrub mode has been selected but the scrub motor is off. This will be the case if the Drive Paddle (3) is in
the neutral position. The scrub motor will stay on for approximately 3 seconds after the Drive Paddle (3) returns to the neutral position.
•
This indicator will be GREEN if the heavy scrub mode has been selected and the scrub motor is on.
•
This indicator will be OFF if the scrub mode is off or if the normal scrub mode has been selected.
Normal Scrub Mode Indicator (30):
•
This indicator will be YELLOW if the normal scrub mode has been selected but the scrub motor is off. This will be the case if the Drive Paddle (3) is in
the neutral position. The scrub motor will stay on for approximately 3 seconds after the Drive Paddle (3) returns to the neutral position.
•
This indicator will be GREEN if the normal scrub mode has been selected and the scrub motor is on.
•
This indicator will be OFF if the scrub mode is off or if the heavy scrub mode has been selected.
Scrub Mode Off Indicator (32):
•
This indicator will be RED if the scrub system is inhibited for any reason. Possible reasons are:
•
The scrub deck has not returned to the UP position.
•
A system fault
•
Low voltage condition
•
This indicator will be GREEN if the system is ready to be placed in either the normal or heavy scrub modes.
•
This indicator will be OFF if either the normal or heavy scrub modes have been selected.
•
This indicator will flash RED if there is a fault in one of the scrub system components. This will be accompanied by an error indication on the Hour Meter
/ Status Display (18).
Brush Remove Indicator (34):
•
This indicator will be YELLOW when it is OK to activate the remove feature, otherwise it will be off.
•
This indicator will be GREEN if the remove process is activated.
Brush Install Indicator (36):
•
This indicator will be YELLOW when it is OK to activate the install feature, otherwise it will be off.
•
This indicator will be GREEN if the install process is activated.
12 - FORM NO. 56041479 / ConvertaMAX
™
34 / I-MAX
™
34HD
Publicidad
Tabla de contenido
