On/Off Button; Switching On Of Ttpro; Motor Search; Switching Off Of Ttpro - Nice TTPRO Instrucciones Y Advertencias Para La Instalación Y El Uso

LED OF FUNCTION DESCRIPTION
STEADY LIGHT Function already present and already set.
LIGHT OFF Function not present.
FLASHING LIGHT Function already present but not yet set , or currently being set.
LED OF LEVEL DESCRIPTION
• RF noise level (V-METER)
This series of LEDs
can have different
• Motor Address
meanings depend-
• Level
ing on the function
• Setting
enabled
CHARGE LED DESCRIPTION
Usb If the USB cable is connected, the BLUE LED is on.
If the USB cable is connected, the GREEN LED flashes when
Chrg
the battery is charging.

3.3 - ON/OFF button

SWITCHING ON/OFF AND MOTOR SEARCH

3.3.1 - Switching On of TTPRO

Press and release the ON/OFF button ( 1 long beep);
01.
scanning of the TTBUS starts automatically, from address 0 to 255 (at this stage
the level LEDs are flashing alternately).
If a motor is found, the OK LED becomes GREEN and, the level LEDs indicate
02.
the address of the motor found (see Table 1).
ADDRESS 1 2 3 4 5 6 7 8 A
Adr 0xFF 1 1 1 1 1 1 1 1 1
Adr 0 0 0 0 0 0 0 0 0 1
Adr 1 1 0 0 0 0 0 0 0 0
Adr 2
0 1 0 0 0 0 0 0 0
Adr 3
0 0 1 0 0 0 0 0 0
TABLE 1
Adr 4 0 0 0 1 0 0 0 0 0
Adr 5 0 0 0 0 1 0 0 0 0
Adr 6 0 0 0 0 0 1 0 0 0
Adr 7 0 0 0 0 0 0 1 0 0
Adr 8
0 0 0 0 0 0 0 1 0
Adr 9 1 0 0 0 0 0 0 0 1
Adr 10 0 1 0 0 0 0 0 0 1
Adr 11 0 0 1 0 0 0 0 0 1
Adr 12
0 0 0 1 0 0 0 0 1
Adr 13 0 0 0 0 1 0 0 0 1
Adr 14 0 0 0 0 0 1 0 0 1
Adr 15 0 0 0 0 0 0 1 0 1
Adr 16 0 0 0 0 0 0 0 1 1
Adr > 16 0 0 0 0 0 0 0 0 1 flashing
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the OK LED turns steady RED.

3.3.2 - Motor search

If TTPRO is already on:
A 01. Press and release the ON/OFF button ( 1 long beep);
scanning of the TTBUS starts automatically.
If a motor is found, the OK LED turns GREEN and, the level LEDs indicate the
address of the motor found (decode the address with the help of Table 1).
B
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the OK LED turns steady RED.
02. To search for another motor connected to the same BUS:
• if the motor has a higher address than the current one, press the + button;
• if the motor has a lower address than the current one, press the – button.
C
If a motor is found, the OK LED turns GREEN and the level LEDs indicate the ad-
dress of the motor found (decode the address with the help of Table 1).
If at the end of the search no motor is found, TTPRO emits 2 short beeps and
the OK LED turns steady RED.

3.3.3 - Switching Off of TTPRO

01. Press and hold the ON/OFF button for about 3 sec.
02. Release the button when TTPRO emits 1 beep and the RED LED starts to
flash quickly.
• TTPRO turns off automatically after 1 minute of inactivity.
English – 4