Publicidad
Idiomas disponibles
Idiomas disponibles
5.
LCD DISPLAY- Indicates all the functions, as
they are occurring, with the CD.
6.
OPEN/CLOSE- Pressing will open or close the
disc tray on the transport.
7.
SGL- To set play mode in single or continuous
play.
8.
TIME- Controls display indication of time mode.
9.
PROGRAM- Depress this button and the unit will
stop and the program indicator will light.
Select each track to be programmed and press
the PROGRAM button between selections. You
can program up to 30 tracks. Press PLAY to
start the program. To exit and erase program,
either hold the program button down for more
than 2 seconds while the unit is stopped, open
the disc tray, or turn off the power.
10.
TRACK SELECT/SEARCH-
a.
Rotation – selects tracks
b.
Pressing while rotating – selects tracks
+10
c.
Pressing once- Puts wheel in search
mode.
PITCH-
11.
actives the pitch slider and adjusts the
amount of control the pitch slider has on the overall
speed of music. Tapping the pitch will toggle slider
between 8% and 16% pitch ranges.
pitch for 3 seconds will deactivate the pitch control.
23.
Power Switch- Turn on and turn off the
machine with this button. The unit should
always be shut down with this button first
before any external power is removed.
Typically, it is recommended that the CD player
is powered on before amplifiers and off after
amplifiers to avoid an audio spike to be sent
through your equipment.
24.
IEC Power Plug Connector - Plug your supplied
power cord in here.
25.
Voltage Selector - Set this switch to the voltage
for your location.
26.
RCA Audio Connectors - Connect your CD
player to your mixer from this line level output.
27.
Digital Output - The format is type 2, form 1,
also known as S/PDIF (Sony/Phillips Digital
Interface Format). In order to use the digital
output you should not use variable pitch slider
and the pitch bend buttons. If you adjust the
pitch, other devices may not read the digital
output properly because the sampling rate
changes
28.
Relay Connector- If you wish to use the relay
function plug in your 3.5mm stereo control
cables into here and then into your other unit.
The cable must be a stereo style plug for the
units to work properly
Holding the
12.
BPM- Switches the mode of the display between
showing the BPM and the percentage change in
pitch.
13.
-,+ - Works as pitch bend and controls key and
pitch functions.
14.
PITCH SLIDER- Controls the overall speed of
the music.
15.
PITCH RANGE LED- Indicates current pitch
range of the pitch slider
16.
LOOP IN- Used to set stutter and loop in points.
17.
LOOP OUT- Used to set loop out points and
release the loop.
18.
RELOOP/STUTTER- Used for repeated play
(stutter) from the loop in point, repeating a
previously set, and hot start.
RELAY- Used for setting Alternating play start
19.
between attached units.
20.
TAP- Tap this button with the beat of the music to
determine the current Beats Per Minute (BPM).
21.
CD Illumination Light (unit front) – lights up
the CD drawer and CD when open.
22.
CD Drawer (Unit Front) – Place your CDs you
wish to play in here. This unit is designed to
play commercially available CD and properly
burned and finalized CDR. Due to variances on
the specification of certain CD burners and CDs
some discs home made CDs may not play
properly.
29.
Remote Start Connector – Use this connector to
plug into your fader start compatible mixer or
remote switch. This function is always active.
To use this connector for fader start, connect
the supplied fader start cable to a fader start
compatible mixer. Every time you move the
crossfader on the mixer over to the side that
the unit is on, it will automatically start playing.
When you move the fader away from that side,
the unit will stop. Moving the fader back to the
unit side will start play again.
Publicidad
