American Standard BOULEVARD 2891 Manual Del Usuario página 2

3
CLOSET
FLANGE
A
CLOSET
BOLTS
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide into
place 6" (152mm) apart and
parallel to wall.
6
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl
down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
!
OR BASE MAY BE DAMAGED!
b. Install bolt covers:
1. Make sure that the bolt cover area on the toilet is clean and
dry (see figure). Use a dry piece of cloth or soap and water
if needed.
2. Take plastic bolt cover and peel the brown protective film off
on both ends. The adhesive part is now visible and ready to
be placed on the toilet (see figure).
3. Gently place the bolt cover on the toilet area (see picture) and if
everything is aligned, push bolt cover firmly so it remains in place.
4. If not aligned, you can still take it off and put it back so it is aligned.
5. Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet.
6. After 24 hours, the bolt cover adhesive has completely set off and if needed, you can remove/replace
as needed. The dual lock technology is now in place.
c. Smooth off the bead of sealant around base. Remove excess sealant.
7
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8a
Before continuing, determine the type of water supply connection you have from the chart
below and use the appropriate assembly parts required to properly reconnect the water supply.
DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
4
SEALANT
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent
damage), and install wax ring evenly around
waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant
around toilet base.
METAL FLANGED METAL SPIRAL
TUBING TUBING
LOCK NUT
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing Use existing spiral cone
coupling nut washer. Fluidmaster
and washer. cone washer may not
seal completely on
spiral type supply line.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
5
OPENING
CLOSET
WAX RING
POSITION TOILET ON FLANGE
a.
b.
BOLTS
RECOMMENDED
VINYL/BRAIDED
CONNECTOR
LOCK NUT LOCK NUT
EXISTING
COUPLING
CONE
NUT
WASHER
COUPLING
NUT
WATER WATER
SHUT-OFF SHUT-OFF
Captive cone washers
already included. No
additional washers needed.
- 2 -
NUT
WASHER
FLANGE
BOLT
Unplug floor waste opening and install toilet on closet
flange so bolts project through mounting holes.
Loosely install retainer washers and nuts. Side of
washers marked "THIS SIDE UP" must face up!
Peel both protective films off
and stick bolt cover to toilet.
CLOSET FLANGE
8b
With correct washers in place (see
Step 8a), tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
BOLT COVER
Back Side
Front Side
BOLT COVER
NUT
CLOSET BOLT
73016 9 0- 100 Rev. C