American Standard Boilevard 2891 Instrucciones De Instalación

INSTALLATION INSTRUCTIONS
BOULEVARD - 1.28 gpf/4.8 Lpf One-Piece Toilet
®
Model 2891 - Elongated Right Height
TROPIC - 1.28 gpf/4.8 Lpf One-Piece Toilet
®
Model 2786 - Elongated Right Height
TOWN SQUARE
®
Model 2847 - Elongated Right Height
TOWN SQUARE
®
Model 2851A - Elongated Right Height
Thank you for selecting American Standard – the benchmark of fine quality for over 140 years. To ensure this product is installed properly, please read
these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Regular Screwdriver
Wax Ring/Gasket
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
2
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
Model 2891 - BOULEVARD 1.28 gpf/ 4.8 Lpf
FINISHED WALL
29-3/4"
(756 mm)
7-1/2"
(192 mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
18-1/2"
(470 mm)
8-1/2" 13-1/2"
(217 mm) (345 mm)
12"
(305 mm)
IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2019
- 1.28 gpf/4.8 Lpf One-Piece Toilet
S - 1.28 gpf/4.8 Lpf One-Piece Toilet
Adjustable Wrench
Flexible Supply Tube
14-1/2"
(368 mm)
14"
(350 mm)
SUPPLY
AS
REQUIRED
(position 1 or
position 2)
16-1/2"
3-3/4"
(419 mm)
(95mm)
9"
5-1/2"
(229mm)
(140mm)
(152mm)
FINISHED 14-1/4"
FLOOR (364 mm)
with Seat
®
with Seat
®
with Seat
®
with Seat
®
Putty Knife Sealant
Closet Bolts Hacksaw
Model 2786 - TROPIC 1.28 gpf/ 4.8 Lpf
FINISHED WALL
8-1/8"
(206 mm)
30-1/2"
(778 mm)
6"
8-1/2"
(217 mm)
12"
(305 mm)
IMPORTANT: Water supply on the wall is required at 3-3/4" or 9" from centerline of the toilet (see rough-in).
First suggested position is hidden behind the toilet. The geometry of the toilet gives space for this installation.
The second suggested position is next to the toilet. Between these two positions, the space for the supply
between wall and toilet is limited to 3-1/4". In this case, check your supply and hose dimensions.
Carpenters Level
Tape Measure
29-3/4"
(756 mm)
C/L OF SEAT POST
HOLES 5-1/2"
(140mm) CENTERS
SUPPLY AS
REQUIRED
18-1/2"
(position 1)
(470 mm)
OR
SUPPLY AS
REQUIRED
(position 2)
16-1/2"
(419 mm)
5-1/2"
(140mm)
13-1/2"
FINISHED
(345 mm)
FLOOR
C/L OF OUTLET AND
TOILET MTG BOLTS
16-3/4"
(424 mm)
14"
(355 mm)
30-1/2"
(778 mm)
3-3/4"
(95mm)
9"
(229mm)
6"
(152mm)
14"
(354 mm)
7301450-100 Rev. 3 8/19