Audio-Technica M3 Serie Configuración Y Funcionamiento página 7

Ocultar thumbs Ver también para M3 Serie:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

P52002_M3-System_OM
2/27/08
How to make setting changes on the M3T Stereo Transmitter
To access the M3T Stereo Transmitter's user-changeable functions,
Touch the Mode/Set button. The top line of the transmitter display
shows " FREQ ". Touch the Down arrow button to scroll through the
functions that may be changed. Note that for Frequency, Trim, RF
Power, HP Out, the display's lower line indicates the current setting
for the given function.
M3T Stereo Transmitter Functions
Function Menu
▲▼ Frequency
▲▼ Group
▲▼ User
▲▼ Trim
▲▼ RF Power
▲▼ HP Out (Headphones Output)
▲▼ Program
▲▼ Reset
▲▼ Quit (exit Menu)
* Continue in the same Up/Down direction and choices "wrap around" to the other end of the range.
Frequency (Transmitter)
Permits manual selection of a frequency. See How to Select a
Frequency , page 11.
Group (Transmitter)
Permits selection of frequency groups with pre-coordinated channels.
There are six frequency groups, each offering 16 pre-coordinated
channels. See How to Select a Frequency , page 11.
User (Transmitter)
Permits selection (optional) from among three user-created frequency
groups. See How to Select a Frequency , page 11.
Trim (Transmitter)
Controls level of both inputs (L/1 and R/2). Trim levels are set at the
factory to the maximum position (0); adjust if necessary. See Setting
Levels , page 12.
RF Power Adjustment (Transmitter)
Allows you to set RF power to " RF HI " or " RF LOW ". The default
setting is " RF HIGH ." When the setting you prefer is shown, Hold the
Mode/Set button.
9:08 AM
Page 7
Default Value
Lowest in band
G1 - 1
U1 - 1
0
High
Stereo
-
-
QUIT
To change a transmitter function, when the function to be edited is
displayed, touch the Mode/Set button. The small word " EDIT " will flash
in the display. Touch the Up/Down arrow buttons to scroll through the
available choices for the function, stopping on the desired choice. Hold
the Mode/Set button to accept the new choice. " STORED " appears in
the display when the choice is accepted. The transmitter then returns to
Menu mode. Continue this process until all desired function-setting
changes are complete. Note: To escape from Edit mode without
making any changes, touch the Mode/Set button. " ESCAPE "
appears briefly in the display, and the transmitter returns to
Menu mode.
Choices (Edit)
Over 1250 discrete frequencies
G1 – G6 (16 channels each)
U1 – U3 (16 channels each)
0 – Unlimited
Low, High
Stereo, L/R Mix
Create custom frequency groups
Choose OK to restore factory settings
Press Mode/Set once to exit
Headphones Output (Transmitter)
Allows you to switch headphones output between Mix and Stereo. In
the Stereo setting, the L1 signal goes to the left earphone; the R2
signal goes to the right earphone. In the Mix setting, a combined signal
from both the L/1 and R/2 inputs goes to both earphones. When the
setting you prefer is shown, Hold the Mode/Set button.
Program (Transmitter)
In the event that the preprogrammed frequency groups (available under
the Group menu) do not meet your requirements, Audio-Technica
allows you to program custom frequency groups. See How to Select a
Frequency , page 11.
Reset (Transmitter)
Allows you to reset all transmitter functions to their factory-default
values. Hold the Mode/Set button while " RESET " is displayed in the
LCD window. At the prompt " OK? " hold the Mode/Set button again.
Factory-default settings will be restored.
Quit (Transmitter)
To exit the Edit mode, press the Down arrow until " QUIT " is displayed
in the LCD window. Then press the Mode/Set button once to exit the
menu. The " AF " scales will reappear in the window, indicating the
return to normal operation.
7
EN
Wrap-around*
Yes
Yes
Yes
No
Yes
Yes

Publicidad

Tabla de contenido
loading

Productos relacionados para Audio-Technica M3 Serie

Este manual también es adecuado para:

M3tlM3tM3r

Tabla de contenido