Publicidad
Idiomas disponibles
Idiomas disponibles
Select Custom Settings
To display current settings, tap the Timeout (
or PIR Sensitivity (
) button. The indicator LED (
P
illuminate.
Change Settings
1
Press and hold the desired programming button (
(about 3 seconds).
2
Tap the same programming button to cycle to your desired setting.
3
Press and hold the same programming button until the
(about 3 seconds).
Default settings
are shown in bold
IL
Indicator LEDs
Timeout Button
30 minutes
15 minutes
5 minutes
1 minute
Sensor Mode Button
Occupancy
1
(Auto-ON / Auto-OFF)
Occupancy with Learning ALD
2
Occupancy with Fixed ALD
3
Vacancy
1
(Manual-ON / Auto-OFF)
M
Sensor LED (behind lens)
Pulses green for ultrasonic and amber
for PIR detection during Test mode.
1
Sensor Mode is locked as "Vacancy" in the MS-A102-V (Vacancy model).
2
ALD (Ambient Light Detection) Learn mode will turn lights on only if natural light in room is low. If
switch turns on when there is enough natural light, or if switch does not turn on when there is not
enough natural light, press the tap button within 5 seconds of entering the room. Over time, the
switch will learn your preferred setting.
3
ALD (Ambient Light Detection) Fixed mode will turn the lights on only if natural light in room is low. The
light level at which lights will automatically turn on (or stay off) can be adjusted through the "Set ALD
Fixed Level" setting in "Additional Settings" section.
Technical Assistance: www.lutron.com
®
), Sensor Mode (
), Ultrasonic Sensitivity (
M
) that corresponds to the current setting will
IL
,
,
, or
) until an
begins to flash
M
P
IL
goes solid to lock your selection
IL
Tap button
(tap on/off)
Ultrasonic Sensitivity
Button
High
30
m
Hi
Medium
15
Med
Low
5
Low
Off
1
Off
Mode
PIR
PIR Sensitivity
Occ
Button
Hi
Lrn
Med
High
Fixd
Low
Medium
Vac
Min
Low
Minimum
Ultrasonic Transducers
PIR Lens
|
U.S.A., Canada, Caribbean: 1.800.523.9466
Additional Settings
Note: All programming options and additional info are available at
),
www.lutron.com/DTMaestroInstall
Test Mode
Test Mode is a short timeout (less than 15 seconds) that will test the coverage of the sensor at the
current settings.
To enable Test Mode:
1. Wait 2 minutes after initial power up.
2. Press and hold
T
3. The device will exit Test Mode automatically after 5 minutes of inactivity, or when any button is
pressed.
Note: An amber LED flashes to indicate PIR detection, a green LED flashes to indicate ultrasonic
detection. You may hold
sensitivity of that specific technology.
Restore Default Settings
Press and hold
sensor's settings back to their defaults.
T
Off-While-Occupied
When Off-While-Occupied is Enabled: After manual shutoff, the sensor will keep lights off as long
as the space is occupied and the timeout has not expired. This setting is best for rooms where
presentations are given and lights may be kept off during occupancy. This is the default setting.
When Off-While-Occupied is Disabled: After manual shutoff, the sensor will keep lights off for
25 seconds before looking for motion. If motion is detected, the lights will turn back on. This
setting is best for high‑traffic areas like bathrooms and hallways.
Change Setting:
1. Press and hold
2. Tap
to cycle to your desired setting.
P
3. Press and hold
P
IL
P
Off-While-Occupied Disabled
Off-While-Occupied Enabled
Setting Fixed ALD Level
The light level you set will determine when a unit set in "ALD Fixed" sensor mode will turn lights
on, or keep lights off, upon detecting occupancy. This setting only affects the behavior of a sensor
in "ALD Fixed" mode.
Change Setting:
1. Press and hold
M
2. The Ambient Light Detect light level will now be displayed on the
your desired setting.
3. Press and hold
M
Light Level
IL
High: turns lights ON unless room is very bright
Medium
Low
(Default when in ALD Fixed mode)
Minimum: turns lights ON only when room is dark
|
Mexico: +1.888.235.2910
|
Others: +1.610.282.3800
until the PIR lens flashes (about 7 seconds).
or
for 2 seconds while in test mode to test the current
P
and
until all
blink slowly (about 7 seconds). This will restore ALL of the
P
IL
and
P
at the same time until an
IL
begins to flash (about 3 seconds).
until the
IL
goes solid to lock your selection.
(Default)
and
until an
IL
begins to flash (about 3 seconds).
until the
IL
goes solid to lock your selection.
. Tap
to cycle to
IL
M
Publicidad
