Publicidad
Idiomas disponibles
Idiomas disponibles
Select Custom Settings
To display current settings, tap the Timeout (
or PIR Sensitivity (
) button. The indicator LED (
P
illuminate.
• Timeout and Sensor Mode settings may have different settings for each circuit. In this case, the
LED for Circuit 1 settings will illuminate, followed by the LED for Circuit 2 settings.
Change Settings
1
Press and hold the desired programming button (
(about 3 seconds). This will change settings for BOTH circuits.
• Timeout (
) and Sensor Mode (
) may be adjusted independently for EACH circuit. Holding
M
or
M
AND
T
or
T
simultaneously will program settings for that specific circuit.
1
2
2
Tap the same programming button to cycle to your desired setting.
3
Press and hold the same programming button until the
(about 3 seconds).
Default settings
are shown in bold
IL
Indicator LEDs
Timeout Button
1
30 minutes
15 minutes
5 minutes
1 minute
Sensor Mode Button
1
(Sensor Mode determines how lights
turn on)
Occupancy
2
(Auto-ON / Auto-OFF)
Occupancy with Learning ALD
3
Occupancy with Fixed ALD
4
Vacancy
2
(Manual-ON / Auto-OFF)
M
Sensor LED (behind lens)
Pulses green for ultrasonic and amber
for PIR detection during Test mode.
1
Using ONLY the
or
to enter programming mode will set BOTH circuits to the new setting.
M
Holding
or
and
or
simultaneously will program settings for that specific circuit.
M
T
T
1
2
2
Circuit 1 Default: Occupancy; Circuit 2 Default: Vacancy.
3
Learning ALD (Ambient Light Detection) mode: Lights remain off if enough natural light is present.
If the lights turn on and the user doesn't want that much light, the user can tap the button within
5 seconds of entering the room. Similarly, if the lights don't turn on when entering a space and the
user wants more light, the user can tap the button within 5 seconds of entering the room. Over time,
the sensor will learn the user's preferred light level.
4
Fixed ALD mode: Lights turn on only when there is less than a set amount of natural light available.
The set level can be adjusted in "Fixed ALD Level" settings.
Customer Assistance: www.lutron.com/support
®
), Sensor Mode (
), Ultrasonic Sensitivity (
M
IL
) that corresponds to the current setting will
,
M
,
, or
P
) until an
IL
begins to flash
IL
goes solid to lock your selection
Circuit 1
Tap button
(tap on/off)
Circuit 2
Tap button
(tap on/off)
Ultrasonic Sensitivity
Button
High
30
m
Hi
Medium
15
Med
Low
5
Low
Off
1
Off
Mode
PIR
PIR Sensitivity
Button
Occ
Hi
Lrn
Med
High
Fixd
Low
Medium
Vac
Min
Low
Minimum
Ultrasonic Transducers
PIR Lens
|
U.S.A., Canada, Caribbean: 1.844.LUTRON1
Additional Settings
Note: Additional product information, including "Circuit Swapping", and other programming options
),
and wiring diagrams are available at www.lutron.com/DTMaestroInstall
Test Mode
Test Mode is a short timeout (less than 15 seconds) that will test the coverage of the sensor at the
current settings.
To Enable Test Mode:
1. Wait 2 minutes after initial power up.
2. Press and hold either
3. The device will exit Test Mode automatically after 5 minutes of inactivity, or when any button is
pressed.
Note: An amber LED flashes to indicate PIR detection, a green LED flashes to indicate ultrasonic
detection. You may hold
sensitivity of that specific technology.
Restore Default Settings
Press and hold
and
sensor's settings back to their defaults.
Off-While-Occupied
When Off-While-Occupied is Enabled: After manual shutoff, the sensor will keep lights off as long
T
as the space is occupied and the timeout has not expired. This setting is best for rooms where
1
presentations are given and lights may be kept off during occupancy. This is the default setting.
When Off-While-Occupied is Disabled: After manual shutoff, the sensor will keep lights off for
25 seconds before looking for motion. If motion is detected, the lights will turn back on. This setting
T
is best for high-traffic areas like bathrooms and hallways.
2
Change Setting:
1. Press and hold
and
2. Tap
P
to cycle to your desired setting.
3. Press and hold
P
until the
Setting Fixed ALD Level
1. a. For Circuit 1: Press and hold
b. For Circuit 2: Press and hold
IL
Off-While-Occupied Disabled
Off-While-Occupied Enabled
P
2. The Ambient Light Detect light level will now be displayed on the
your desired setting.
3. Press and hold
until the
M
Light Level
IL
High: turns lights ON unless room is very bright
Medium
Low
(Default when in ALD Fixed mode)
Minimum: turns lights ON only when room is dark
Troubleshooting
Symptoms
After installation:
• Sensor switch does not respond to
button presses
OR
• Sensor switch worked only once or
doesn't work at all
Lights do not turn ON when space is
occupied
For additional features, wiring help, troubleshooting, and product information please visit: www.lutron.com/DTMaestroInstall
|
Mexico: +1.888.235.2910
or
T
until the PIR lens flashes (about 7 seconds).
T
1
2
or
for 2 seconds while in test mode to test the current
P
until all
IL
blink slowly (about 7 seconds). This will restore ALL of the
P
P
at the same time until an
IL
begins to flash (about 3 seconds).
IL
goes solid to lock your selection.
and
until the
begins to flash (about 3 seconds).
M
IL
and
until the
begins to flash (about 3 seconds).
M
P
IL
IL
goes solid to lock your selection.
Possible Causes / Solutions
• Black wire is not connected to Line / Hot. Swap black and red wires.
• Check wiring; ground wire must be connected for product to function.
• Wait 10 seconds.
• Off-While-Occupied mode is Enabled and the timeout has not expired.
• Sensor mode is set to Vacancy.
• Sensor is set to one of the Ambient Light Detection (ALD) settings and the room
is too bright for the current light level setting.
• Sensor does not have full view of the room. Move objects blocking line-of-sight.
|
Others: +1.610.282.3800
. Tap
to cycle to
IL
M
Publicidad
